UTE UH2-44-SET Скачать руководство пользователя страница 65

Страница: 65 / 76

UH2-44: 4x4 HDMI 2.0 HDBaseT Matrix Switcher

U.T.E. electronic GmbH & Co. KG

www.ute.de

8. Firmware Upgrade

Please follow the steps as below to upgrade firmware by the

port on the rear

panel:

Prepare the latest two

upgrade files and rename them as “08010000.APP” and

“08010000.APS” on PC.

Power off the switcher, and connect the

port of switcher to the PC with USB

cable.

Power on the switcher, and then the PC will automatically detect a U-disk named of

“BOOTDISK”.

Double-click the U-

disk, a file named of “READY.TXT” would be showed.

Directly copy one

of two upgrade files (e.g. “08010000.APP”) to the “BOOTDISK”

U-disk.

Reopen the U-

disk to check the filename “READY.TXT” whether automatically

becomes “SUCCESS.TXT”, if

yes, the firmware was updated successfully,

otherwise, the firmware updating is fail, the name of upgrade file should be confirm

again, and then follow the above steps to update again.

Repeat step 5~6 to copy the other upgrade file

(“08010000.APS”) to the

“BOOTDISK” U

-disk.

Remove the USB cable after firmware upgrade.

After firmware upgrade, the switcher should be restored to factory default by

sending command.

Содержание UH2-44-SET












































































Результаты поиска

Содержание UH2-44-SET

Отзывы:

Похожие инструкции для UH2-44-SET

Бренды по названию

Популярные бренды

UTE UH2-44-SET, Руководство пользователя

Результаты поиска

Содержание UH2-44-SET

Отзывы:

Похожие инструкции для UH2-44-SET

Бренды по названию

Популярные бренды