UTE UH2-44-SET Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 76

background image

UH2-44: 4x4 HDMI 2.0 HDBaseT Matrix Switcher

U.T.E. electronic GmbH & Co. KG

14

www.ute.de

4.5 Audio Setting

The matrix switcher provides four analog L+R audio output ports and four digital
SPDIF output ports for audio de-embedding. The audio source selection of these eight
audio output ports, and the L+R audio volume can be controlled by the front panel
buttons.

4.5.1 Audio Source Selection

There are eight audio sources can be selected for any analog L+R audio output port,
and twelve audio sources can be selected for any SPDIF audio output port.

Audio Output Ports

Audio Sources

Input Breakout

Output Breakout

ARC

L+R OUT 1

In1 Breakout
In2 Breakout
In3 Breakout
In4 Breakout

Out1 Breakout
Out2 Breakout
Out3 Breakout
Out4 Breakout

/

L+R OUT 2
L+R OUT 3
L+R OUT 4

SPDIF OUT 1

In1 Breakout
In2 Breakout
In3 Breakout
In4 Breakout

Out1 Breakout
Out2 Breakout
Out3 Breakout
Out4 Breakout

Out1 ARC
Out2 ARC
Out3 ARC
Out4 ARC

SPDIF OUT 2
SPDIF OUT 3
SPDIF OUT 4

Example: Select the HDMI input 2 audio source for the analog L+R output 2.

Press

Press

to select

AUDIO Setting

.

Press

to enter the tab.

Press

to

select

L+R OUT 2

.

Press

Press

to select

In2 Breakout

Press

to confirm.

AUDIO Setting <
IP Address

L+R OUT 2 <
L+R OUT 2 Vol

L+R OUT 2
In2 Breakout

<

«
...
19
20
21
22
23
...
»

Содержание UH2-44-SET













































































Отзывы:

Нет отзывов

Похожие инструкции для UH2-44-SET

Бренд: Vector Страницы: 6

Бренд: K-Dyne Страницы: 10

Бренд: Inline Страницы: 26

Бренд: LIVOLO Страницы: 14

EdgeSwitch 10 XP

Бренд: Ubiquiti Страницы: 13

Бренд: Clever Little Box Страницы: 15

Бренд: Tripp Lite Страницы: 12

Бренд: 3onedata Страницы: 2

Бренд: Manhattan Страницы: 4

SEHI SEHI100TX-

Бренд: Cabletron Systems Страницы: 75

Бренд: HDTV Supply Страницы: 21

Бренд: I-Tech Страницы: 19

Бренд: Linkskey Страницы: 2

Бренд: WAGO Страницы: 36

SL-3-SL-4 STOP LIGHT SWITCH

Бренд: BENDIX Страницы: 4

Бренд: Velleman Страницы: 4

NSwitch Outdoors

Бренд: Moxa Technologies Страницы: 30

Бренд: WELLTECH Страницы: 280

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды