background image

 

TVE-DEC12 User Manual 

Important information 

Limitation of liability 

To the maximum extent permitted by applicable law, in no event will UTCFS be liable 
for any lost profits or business opportunities, loss of use, business interruption, loss of 
data, or any other indirect, special, incidental, or consequential damages under any 
theory of liability, whether based in contract, tort, negligence, product liability, or 
otherwise. Because some jurisdictions do not allow the exclusion or limitation of liability 
for consequential or incidental damages the preceding limitation may not apply to you. 
In any event the total liability of UTCFS shall not exceed the purchase price of the 
product. The foregoing limitation will apply to the maximum extent permitted by 
applicable law, regardless of whether UTCFS has been advised of the possibility of 
such damages and regardless of whether any remedy fails of its essential purpose. 

Installation in accordance with this manual, applicable codes, and the instructions of the 
authority having jurisdiction is mandatory. 

While every precaution has been taken during the preparation of this manual to ensure 
the accuracy of its contents, UTCFS assumes no responsibility for errors or omissions. 

Advisory messages 

Advisory messages alert you to conditions or practices that can cause unwanted 
results. The advisory messages used in this document are shown and described below. 

 

WARNING: 

Warning messages advise you of hazards that could result in injury or loss 

of life. They tell you which actions to take or to avoid in order to prevent the injury or 
loss of life. 

 

Caution

: Caution messages advise you of possible equipment damage. They tell you 

which actions to take or to avoid in order to prevent the damage. 

 

Note

: Note messages advise you of the possible loss of time or effort. They describe 

how to avoid the loss. Notes are also used to point out important information that you 
should read. 

 

Содержание Interlogix TVE-DEC12







































Отзывы: