Installation
Use the following guidelines when adding this keypad to your
Simon 3 system:
•
Program the keypad as key or chime mode.
•
Program (learn) the keypad into the control panel as a
sensor.
•
Program key mode keypads using sensor groups 01, 03,
06, or 07 for nonsupervised use.
•
Program chime mode keypads using sensor groups 01.
03. 06, or 07 for nonsupervised use or sensor groups 00,
02, 04, or 05 for supervised use.
•
You must delete and reprogram the keypad into panel
memory every time you change the keypad operating
mode.
•
Each learned keypad uses one of the available sensor
numbers (24 total sensors/zones are available with the
Simon 3 panel).
•
When you mount the keypad on the wall, it might not work
properly if you mount it too close to the Simon 3 panel.
Programming
For complete programming instructions, refer to your Simon 3
installation instructions. The keypad must be programmed for
key or chime mode before programming into panel memory.
To program the keypad mode, do the following:
1. Remove the mounting plate on the back of the keypad.
2. Insert two of the three batteries into the keypad.
3. While holding down the Lights on and Lights off keys,
insert the third battery. Release the keys. The keypad will
sound one long beep.
Note:
To check the software version of the keypad, press 1
after this step.
4. Immediately press 8 to program the keypad for key mode.
The keypad announces
no chime hello, touchpad okay
.
Or press 9 to program the keypad for chime mode. The
keypad announces
chime hello, touchpad okay
.
The chime and no chime announcements from the keypad only
describe the keypad mode being programmed. The
announcements do not describe doors and special motion
chime functions programmed at the panel.
After programming the mode, the keypad must be programmed
(learned) into the panel.
To program the keypad into panel memory, do the following:
1. Open the control panel cover.
2. Enter utility access code 1 or 2 using the red-numbered
keys.
3. Press Add. The panel announces
select from main
menu
.
4. Press Sensor/remote. The panel announces
press button
on sensor
.
5. Press the Lights off button on the keypad six times in rapid
succession. On the sixth key press, the keypad makes a
long beep. The keypad announces
okay
to indicate that it
has been learned into the panel. The panel announces
keychain remote
.
Note:
If the keypad does not announce
okay
, press Cancel at
the panel and repeat the process.
6. Press Sensor/remote repeatedly until you hear the sensor
name or item you want to use. Each name may be used
more than once. For a more specific location name, press
Option # for compass directions (north, northeast, east,
southeast, south, southwest, west, northwest).
7. Press Done when you hear the desired sensor name. The
panel announces
use numbered keys to enter sensor
group
.
8. Enter the two-digit sensor group (key mode: 01, 03, 06, or
07; or chime mode: 00 through 07). The panel announces
the sensor group and the first available sensor number,
then prompts you to press Done to accept. If you wish to
use a sensor number other than the next available one,
use the numbered keys to enter a two-digit sensor number
immediately after entering the sensor group.
9. Press Done. The panel confirms programming by
announcing the sensor number, name, and group.
Sensor test
The keypad is sensitive to its orientation to the control panel.
For that reason, we recommend you test the keypad before
you mount it on the wall.
To test the keypad with the Simon 3 system, do the following:
1. Make sure the panel is disarmed.
2. Open the panel door.
3. Enter the appropriate access code.
4. Press Test. The panels responds with
sensor test, press
again to change or Done to select
.
5. Press Done.
6. The panel will prompt you to trip each sensor one at a
time. To trip the keypad, press and hold the two
emergency buttons simultaneously for three seconds. You
2
Dialog QS1500 Touchtalk Interactive Keypad Installation Instructions
