UTC Fire and Security interlogix DI601AM Скачать руководство пользователя страница 10

Specifications

Detection range

Programmable: 10 m, 20 m 

or 30 m 

Coverage 

10 to 70° detection angle, 30 

x 24 m coverage max.

Adjustment  

-60° to +60° pan, tilt +45°

Fresnel lens

28 zones for each detection 

element, which can be 

masked with the curtain 

sliders

Customized optics

Double silicon shielded quad 

element eliminates 50,000 

Lux of white light

LEDs

Top PCB

Sensor PCB

Red: Programming LED

Blue: Detection alarm
 
Red(small): Anti-mask alarm

Infrared: Walk tester 
communication

Outputs

NO

NC

Silent, solid state, 

magnetically immune. 

Volt free relay, signal contact 

24 VAC/DC at 50 mA with an 

integral 25 Ω series resistor.

Alarm time 5 seconds.

Volt free relay, signal contact 

24 VAC/DC at 50 mA with an 

integral 25 Ω series resistor.

Alarm time 5 seconds.

Fault/Mask

Volt free relay, signal contact 

24 VAC/DC at 50 mA with an 

integral 25 Ω series resistor

Power input

10 to 15 V DC

Current

16 mA (12 V nominal) 

Standby 27 mA MAX

Pulse count

1 or 2

Temperature 

compensation 

Analogue (thermistor) and 

digital sensitivity adjustment

Control 

Digital microprocessor with 

non-volatile memory

Walk test

Output test mode with LED 

indication. Option to disable 

LEDs.

Operating temperature

−30 to +65°C

Housing

High impact ABS plastic with 

HDPE cover, UV stabilized

Dimensions W x H x D

125 x 175 x 130 mm

Weight

348g Net, 534 g Gross 

Mounting height

Variable up to 6 m 

Optimum height 3 m for full 

range

Regulatory information

Manufacturer 

UTC Fire & Security Americas 

Corporation, Inc.

1275 Red Fox Rd., Arden Hills, MN 

55112-6943, USA 

Authorized EU manufacturing 

representative:

UTC Fire & Security B.V.

Kelvinstraat 7, 6003 DH Weert, 

Netherlands

Certification

EN50130 

EN50131

EN50130-5

EN50131-2-2, Grade 3, Class IV

Certified by Telefication B.V

Note: EN50131-2-2 compliant only 

when mounted at 1.5m and 3m.

Environmental class

IP65

This product meets the 

environmental requirements of 

EN50130-5.

2002/96/EC (WEEE directive): 

Products marked with this symbol 

cannot be disposed of as unsorted 

municipal waste in the European 

Union. For proper recycling, return 

this product to your local supplier 

upon the purchase of equivalent 

new equipment, or dispose of it 

at designated collection points. 

For more information see: www.

recyclethis.info.

Contact information

www.utcfireandsecurity.com or www.interlogix.com.

For customer support, see www.interlogix.com/customer-

support

Содержание interlogix DI601AM











Отзывы: