Usr EV20i Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 65

background image

21

AC PARALLEL OPERATION APPLICATIONS

Substantial overloading that continuously lights the overload indicator
light (red) may damage the generat

or. Marginal overloading that

temporarily lights the overload indicator

light (red) may shorten the

service life of the generator.

For single generator operation, the parallel operation kit must be
removed.

Never connect or remove the parallel operation kit when the
generator is running.

Use only a

USR

approved parallel operation kit (optional

equipment) when connecting two generators for parallel

operation

.

Never connect different generator models and types.

Make sure that the electrical rating of the tool or appliance does not
exceed that of the generator. Never exceed the maximum power
rating of the generator. Power levels between rated and maximum
may be used for no more than 30 minutes.

If an appliance begins to operate abnormally, becomes sluggish or
stops suddenly, turn it off immediately. Disconnect the appliance,
and determine whether the problem is the appliance, or if the rated
load capacity of the generator has been exceeded.

Make sure that it is in good working order. Faulty appliances or
power cords can create a potential for electrical shock.

Before connecting an appliance or power cord to the generator:

Follow the instructions included with the parallel operation kit.

«
...
21
22
23
24
25
...
»

Содержание EV20i


































































Отзывы:

Нет отзывов

Похожие инструкции для EV20i

Бренд: Caliber Страницы: 10

Бренд: Califone Страницы: 11

Бренд: R&S Страницы: 59

Бренд: Sven Страницы: 6

Бренд: Champion Страницы: 29

Architectual AM15

Бренд: Martin Audio Страницы: 1

Бренд: Westinghouse Страницы: 79

Бренд: Tangent Страницы: 60

Бренд: Craig Страницы: 7

Бренд: Lafayette Страницы: 7

Бренд: Kenwood Страницы: 25

Бренд: Sepura Страницы: 166

Бренд: Hyundai Страницы: 32

Бренд: Time Electronics Страницы: 16

Pop Midi with Bluetooth

Бренд: PURE Страницы: 26

Бренд: ACOPOWER Страницы: 8

Бренд: Audiovox Страницы: 33

Бренд: LOTRONIC Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды