background image

3

g. LIMITATIONS OF LIABILITY. TO THE FULLEST EXTENT PERMITTED BY LAW, NEITHER USI NOR ITS SUPPLIERS 

SHALL BE RESPONSIBLE OR LIABLE WITH RESPECT TO ANY SUBJECT MATTER OF THIS AGREEMENT OR TERMS OR 

CONDITIONS RELATED THERETO UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER THEORY FOR (A) 

LOSS OR INACCURACY OF DATA OR COST OF PROCUREMENT OF SUBSTITUTE GOODS, SERVICES OR TECHNOLOGY, OR 

(B) ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO LOSS OF REVENUES 

AND LOSS OF PROFITS. TO THE MAXIMUM EXTENT PERMITTED BY LAW, USI AGGREGATE CUMULATIVE LIABILITY 

HEREUNDER SHALL NOT EXCEED THE GREATER OF FIFTY DOLLARS ($50.00) OR THE AMOUNT PAID BY YOU FOR THE 

PRODUCT THAT CAUSED SUCH DAMAGE. 

SOME COUNTRIES, REGIONS, STATES OR PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF REMEDIES  

OR OF INCIDENTAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES, OR THE APPLICABLE TIME PERIODS, SO THE ABOVE  

LIMITATIONS OR EXCLUSIONS MAY NOT APPLY. EXCEPT TO THE EXTENT LAWFULLY PERMITTED, THIS LIMITED  

WARRANTY DOES NOT EXCLUDE, RESTRICT OR MODIFY STATUTORY RIGHTS APPLICABLE TO WHERE THE PRODUCT IS  

SOLD BUT, RATHER, IS IN ADDITION TO THESE RIGHTS. 

h. SEVERABILITY. In the event that any of the provisions of this Contract shall be held by a court or other tribunal of 

competent jurisdiction to be unenforceable, the remaining portions of this Contract shall remain in full force and effect, 

provided that in such event the parties agree to negotiate in good faith substitute enforceable provisions which most 

nearly effect the parties’ intent in entering into this Contract. 

i. CHOICE OF LAW; JURISDICTION. This Contract shall be governed by and construed in accordance with the laws of 

the State of Connecticut, U.S.A., without regard to the choice-of-law principles thereof that would result in the 

application of the laws of a State other than Connecticut. Any dispute between the parties arising under or relating to 

this Contract shall be subject to the exclusive jurisdiction of the United States District Court for the District of 

Connecticut, state or the State courts sitting in the Judicial District of Middlesex County, Connecticut. A printed version 

of these Terms will be admissible in judicial and administrative proceedings based upon or relating to these Terms 

to the same extent and subject to the same conditions as other business documents and records originally generated 

and maintained in printed form. 

Note:

 You will be charged for the replacement of any parts which are damaged as a result of improper packaging.

READ ME FIRST!

This manual contains all the information you need to properly unpack, operate and maintain your USI Laminator.  Before 

unpacking your laminator we suggest you read and follow the manual step by step.  It contains essential information about 

each and every facet of your laminator.  Pay special attention to the work environment and safety precautions necessary for 

your laminating unit.

The manual is organized in the following way:

• 

There are seven major chapters, each covers a different subject heading.

• 

Each chapter is further broken down into parts.

• 

Each part contains a detailed discussion, including photographs and figures, 

covering either an operation or maintenance procedure for your laminator. 

• 

Photographs and figures are numbered on each page for quick reference.

• 

Please pay special attention to particular notes and caution statements.

• 

These comments alert you to information the we feel essential to operator 

safety and damage prevention to the laminator.

Copyright Information:

IMPORTANT: This manual is copyright protected by USI, Inc. in accordance with the laws and requirements of the United 

States Government.  Any reproduction of this manual, in part or in full, without the written permission of USI, Inc. constitutes 

a violation of the U.S. copyright laws and is subject to prosecution.

Содержание CSL2700



































Отзывы: