USAlert watchdog Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 16

background image

Push to Listen

This option forces the user to push the reset button to “listen” to the message.

Warning: Release of the reset button will also cancel voice storage.

If set to “Yes”, it can be disabled or enabled through the pager’s front panel menu.

LCD Hold Time

The amount of time the LCD displays information before going into standby mode with
only the standby mode icon displayed. Selections are 10, 30, or 60 seconds, or non-limit
that does not turn off the display. Battery life is decreased accordingly with longer display
times.

Back Light Hold Time

The amount of time the back light will remain on once activated. 5, 10, and 30 seconds
are the selections.

Back Light On Option

Sel

ecting the “Press any key” option will not activate the backlight when a message is

received. Selecting the LCD on time” option will activate the backlight when a message is
received. The backlight will activate when pressing any of the pager’s keys or buttons for
either selection.

«
...
10
11
12
13
14
...
»

Содержание watchdog

















Отзывы:

Нет отзывов

Похожие инструкции для watchdog

Бренд: Flex Страницы: 24

teleCOURIER p71

Бренд: ASCOM Страницы: 2

Бренд: Meta System Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды