US Water Systems Matrixx 150-FLCS Series страница 25 Скачать руководство пользователя | Manualshive

Страница: 25 / 30

background image

25

Contact Information

The Contact Information screes is used to provide the customer with contact info

for US Water Systems. There is a link to the website and to our support team.

Regeneration Initiation

There are two options for regenerating the system. Tap on the desired option and press

“

OK

”.

Regenerate Now:

Regenerate Now will que an immediate regeneration and will start instantly.

Regenerate at Next Regen Time:

Regenerate at Next Regen Time will que the system re-

generate at the specified regeneration time chose in the programming.

Programming Using Water Logix App

«
...
23
24
25
26
27
...
»

Содержание Matrixx 150-FLCS Series































Отзывы:

Нет отзывов

Похожие инструкции для Matrixx 150-FLCS Series

DIRTCAL 5462 Series

Бренд: CALEFFI Страницы: 6

Бренд: Zero B Страницы: 19

Бренд: baracuda Страницы: 12

Бренд: O-SO Pure Страницы: 16

EASYpure II UV 1302 Series

Бренд: Barnstead Страницы: 40

Бренд: Rangemaster Страницы: 4

Бренд: esotec Страницы: 32

Бренд: Idea Group Страницы: 11

Бренд: Brita Страницы: 54

Бренд: 3M Страницы: 8

Бренд: vitapur Страницы: 23

Бренд: Waterdrop Страницы: 28

Бренд: Coway Страницы: 34

Бренд: Omega Страницы: 10

Бренд: ROSEDALE Страницы: 4

Бренд: A.J.Antunes Страницы: 20

Aqua Joe AJ-6PSTB

Бренд: SNOWJOE Страницы: 16

Бренд: MiniMax Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды