Urrea RM812B Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 16

Urrea RM812B Скачать руководство пользователя страница 12

12

• Always wear safety goggles and a dust mask
when drilling, especially when drilling above
the level of your head.
• Watch out for flying sparks. Hold the tool so
that any sparks will fly away from the operator
and other persons. Keep all flammable materi-
als away when using this drill.
• Do not touch the workpiece immediately
after operation. It may be extremely hot, and
could burn the skin.

FEATURES

KNOW YOUR TOOL

Before attempting to use this hammer drill, be-
come familiar with all of its operating features
and safety requirements.

WARNING: Do not allow familiarity with the

hammer drill to cause carelessness.
Remember that a fraction of a second of care-
lessness is enough to inflict severe injury.
1. HAMMER DRILL/DRILL SWITCH
2. TRIGGER SWITCH WITH VARIABLE SPEED
3. LOCK-ON BUTTON
4. FORWARD/REVERSE SWITCH
5. LED LIGHT
6. AUXILIARY HANDLE
7. CHUCK
8. DEPTH GAUGE
9. MECHANICAL SPEED-ADJUSTMENT KNOB

ADDITIONAL HANDLE AND DEPTH GAUGE

CAUTION: Make sure that the power tool is
OFF and unplugged before making any adjust-
ment. Turn the auxiliar handle counter clock-
wise to loosen the collar and allow the depth
gauge passes over the chuck, set the proper
position for the work to be performed.

Set the depth gauge if required and adjust the
handle to secure in its place.
The side handle
can be rotated 360
degrees to find a
position that of-
fers better comfort
and eases the op-
eration. The depth
gauge helps to set
the correct depth if you need to measure a
drilled hole. To change the position of depth
gauge, turn the handle clockwise until the
depth gauge is loose enough to slide through
the hole. Set the depth, check it with a metal
rule for a more accurate measurement, and
then readjust the grip of the handle to set the
depth guide into position.

INSTALLING AND REMOVING DRILL BITS

TO INSTALL:
1. To open the chuck jaws, place the chuck key
in one of the three holes located on the chuck.
Turn the key counter-clockwise.
2. Insert the bit into the chuck jaws. Centre the
bit in the chuck jaws, and tighten the bit by
hand to align the chuck jaws.
3. To close the chuck jaws, place the chuck key
in one of the three holes in the chuck. Turn the
chuck key clockwise until the chuck is tight-
ened securely.
TO REMOVE:
1. Insert the chuck key into one of the holes in
the chuck.
2. Turn the chuck key counter-clockwise to
loosen the chuck.
3. Remove the bit.

WARNING: Do not attempt to tighten the

chuck by gripping the front part and turning
the drill on. Damage to the tool and personal
injury may result. Be sure to tighten the chuck
with the chuck key.

VARIABLE SPEED
SWITCH

Your hammer drill
has a variable speed
dial on switch. The
speed is regulated
by the pressure ap-
plied to the switch.

9

2

3

4

5

6

7

8

1

RM812B manual.indd 12

08/06/16 12:21 p.m.

«
...
10
11
12
13
14
...
»

Содержание RM812B

















Отзывы:

Нет отзывов