background image

4.

Hanging the Fan

REMEMBER 

to turn off the power. Follow 

the steps below to hang your fan properly:

Step 1. 

Remove the decorative canopy bottom

cover from the canopy by turning the cover 

counter clockwise.(Fig. 5)

Step 2. 

Remove the mounting bracket from 

the canopy by removing the 1 of 2 screws 

from the bottom of the mounting bracket and 

loosening the other one a half turn from the 

screw head. Next, turn the canopy counter 

clockwise to removing the mounting bracket 

from the canopy. (Fig. 5)

Step 3. 

Pass the 120-volt supply wires 

through the center hole in the ceiling hanger 

bracket as shown in Fig. 6.

Step 4. 

Secure the hanger bracket to the 

ceiling outlet box with the screws and 

washers provided with your outlet box.

Step 5. 

Remove the hanger pin, lock pin and 

set screws from the top of the motor 

assembly. (Fig. 7)

Step 6. 

Route the safety cable and wires 

exiting from the top of the fan motor through 

the collar cover, canopy cover, canopy and 

then through the ball / downrod. (Fig. 7)

Step 7. 

Align the holes at the bottom of the 

downrod with the holes in the collar on top of 

the motor housing (Fig. 7). Carefully insert the hanger 

pin through the holes in the collar and downrod. Be 

careful not to jam the pin against the wiring inside the 

downrod. Insert the locking pin through the hole near 

the end of the hanger pin until it snaps into its locked 

position, as noted in the circle inset of Fig. 7.         

 

WARNING

FAILURE TO PROPERLY INSTALL

LOCKING PIN AS NOTED IN STEP 7

COULD RESULT IN FAN LOOSENING AND

POSSIBLY FALLING.  

 

Figure 6

Ceiling 

hanger

bracket

Mounting screws 

(supplied with 

electrical box)

CUL Listed 

electrical 

box

120V Wires

Washers

Supply wires

Downrod

Hanger pin

Lock pin

Set screws

Canopy

Canopy cover

Collar cover

Pin in locked

position

   

Step 8. 

Tighten two set screws on top of the fan 

motor firmly. (Fig. 7)

Step 9. 

Place the downrod ball into the hanger 

bracket socket. 

 

Step 10. 

Secure the safety cable to the building 

structure with a wood screw. (wood screw not 

supplied)

Figure 5

Ceiling hanger

bracket

Ceiling 

canopy

Canopy 

cover 

Figure 7

Safety cable

Содержание UHP9160














Отзывы: