background image

13.

Specifications

20.94

lbs

24.20

lbs

1.59'

Fan Size

Speed

Volts

Amps

Watts

RPM

CFM

N.W.

G.W.

C.F.

54"

Low

High

120

120

These are approximate measures. They do not include Amps and Wattage used by the light kit.

0.235

0.56

12.08

66.63

64

163

2153.67

5740.41

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, 
and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning:

 Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the

equipment.

NOTE: 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. 

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of 
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Содержание UHP9000
















Отзывы: