background image

MRF-260i B

ASE

S

TATION

Page 13

With the exception of URC's IR-only, broad-based consumer

remotes, none of URC's PC programmable remotes or any of our

Total Control® whole-house equipment are authorized for online

internet sales. Buying URC's PC programmable remotes or any of

our Total Control® whole-house equipment online means buying

equipment that does not have URC's limited warranty. Such

equipment is not eligible for URC tech support or software support,

either.

2. URC'S LIMITATIONS OF LIABILITY

IN NO EVENT SHALL URC BE LIABLE FOR INDIRECT, SPECIAL,

INCIDENTAL, EXEMPLARY, PUNITIVE OR CONSEQUENTIAL

DAMAGES OF ANY KIND OR LOSS OF PROFITS OR BUSINESS

OPPORTUNITY, EVEN IF URC IS ADVISED OF THE POSSIBILITY

OF SUCH DAMAGES.

IN NO EVENT SHALL URC BE LIABLE FOR LOSS OF OR

DAMAGE TO DATA, COMPUTER SYSTEMS OR COMPUTER

PROGRAMS.

URC'S LIABILITY, IF ANY, FOR DIRECT DAMAGES OF ANY

FORM SHALL BE LIMITED TO ACTUAL DAMAGES, NOT IN

EXCESS OF AMOUNTS PAID BY END USER FOR THE URC

EQUIPMENT.

IN NO EVENT SHALL URC BE LIABLE FOR ANY EVENTS

BEYOND ITS CONTROL, INCLUDING ANY INSTANCE OF

FORCE MAJEURE.

IN NO EVENT SHALL URC BE LIABLE FOR THE ACTS OR

OMISSIONS OF END USER OR ANY THIRD PARTY.

THE LIMITATIONS OF LIABILITY MAY NOT APPLY TO END USER

IN WHOLE OR IN PART, WHERE SUCH ARE RESTRICTED

LIMITED OR EXCLUDED BY APPLICABLE LAW AND SUCH

SHALL APPLY TO THE MAXIMUM EXTENT PERMITTED BY

APPLICABLE LAW.

URC SHALL NOT BE HELD RESPONSIBLE FOR THE STATEMENTS

MADE BY OTHERS.

SOME STATES OR JURISDICTIONS DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES, OR ALLOW LIMITATIONS ON

HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE

LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO END USER.

THIS LIMITED WARRANTY GIVES END USER SPECIFIC LEGAL

RIGHTS AND END USER MAY HAVE OTHER RIGHTS WHICH

VARY FROM STATE TO STATE OR JURISDICTION TO

JURISDICTION.

End User Agreement

The terms and conditions of the End User Agreement available at
www.universalremote.com/eua.php  shall apply.

Содержание MRF-260i



















Отзывы: