background image

11

Side-Chain Circuit

The previously described gain reduction circuit is controlled by the control voltage which is
supplied by the side-chain circuit.  The LA-2A is a feed-back style compressor.  This is due
to the fact that the signal that is used to drive the side-chain circuit is affected by the gain
reduced signal.  This signal is first fed into the “Peak Reduction” potentiometer (R2), which
controls the amount of side-chain drive and in turn controls the compression threshold and
amount of gain reduction.  A 12AX7 is then used as a voltage amplifier to increase the
signal level.  A pre-emphasis circuit is provided on the output of the 12AX7.   Originally
designed for broadcast, the LA-2A allowed for side-chain equalization, which allowed the
operator to make the compression more or less sensitive to the voice frequency bands.
For musical applications, this equalization is usually set to a flat frequency response.
Subsequent to the filter, a 6AQ5 provides the signal necessary to drive the electro-

luminescent panel.  EL panels were often used for night-lights and hence are usually
designed to be driven with 120 volts, 60 Hz AC.  They were not designed for audio, and
applying the wide-bandwidth signals that arise in audio applications results in a shortened
lifetime of the part.

Output Circuit

Figure 7 - Schematic diagram of the LA-2A output circuit.

The output circuit is comprised of a 12AX7 which operates as a voltage amplifier followed
by a 12BH7A which operates as a cathode-follower.  This is followed by the output
transformer, which provides impedance matching and a balanced output.

Metering Circuit

The metering circuit in the LA-2A has 3 modes selected by a front-panel switch, allowing
for output level monitoring at +4 and +10 dB as well as gain reduction.  As mentioned

 R9
220K

R10
1.5K

 R12
470K

R14
2.7K

R11
68K

C1

.02

V1A

C7C

30uF

R13
220K

C2

.1

R16

68K

R17

10K

 R15
470K

R18
 1K

R20
 1K

 R19
470K

C3
.1

 R21
100K

C2

.1

R16

68K

C5

10 uF

1

3

4

8

A-24

2

5

V1B

12AX7

12BH7

V2B

V2A

CATHODE
FOLLOWER

VOLTAGE
AMPLIFIER

FROM
  R1

Содержание LA-2A






















Отзывы: