UNITY LAUNDRY SYSTEMS UTS29 Скачать руководство пользователя страница 36

Страница: 36 / 49

Part. 14000002

Rev. 06//2021

ALARM

11.0 CLEARING / RESETING THE ALARM

When error occurs, the controller will signal an alarm automatically with audible sound. Pressing <Start> button will stop

audible alarm sound. Press <Start> button again after troubleshooting. If the error has been resolved or can be ignored, the

computer will go back to “open” or “close” or “locked” status. Or else the controller will alarm again.

11.1 ALARM INFORMATION AND TROUBLESHOOTING

NO.

ALARM NAME

TROUBLESHOOTING

DoorStat Error

Please check the door switch

Over shock

Please check if the load in the machine is too small or too large

Emergency Stop

Please check Emergency stop is released

Door Pin Err

Please check door pin or Lock release cord

Inverter error

Please check the inverter, or check the input of inverter

Error level sensor

Have not adjusted the level sensor, please contact Unity at 1-800-484-3013

#10

Temp sensor of water

Please check temperature sensor of water

#11

Temp sensor of
inverter

Please check temperature sensor of inverter

#14

Overtime of fill

Can’t reach the set level in time. Please check inlet water filters, drain valve open, or check the level
sensor

#15

Overtime of heat

Can’t reach the set temperature in time. Please check the device of heat, or check the temperature sensor

#16

Overtime of drain

There is remaining water in drum. Please check that the drain valve is opening or if there is a blockage

#17

Lubrication time

The times of run can be browsed and be cleared by pressing [START] button for 3 seconds from startup
screen

#18

Invt comm overtime

Unable to receive replay data from inverter. Please check power inverter or the parameter of the inverter

#19

Inv com err

Please check electrical connection and ground

#20

PUNP inverter error

Please contact Unity at 1-800-484-3013

#21

High temp of invt

Clean lint inside machine and check the inverter fan

#33

PUNP inverter alarm

Please contact Unity at 1-800-484-3013

#34

Clear lint of invt

Clean lint inside machine and check the inverter fan

#49

Bkbd comm overtime

Unable to receive replay data from I/0 Board. Please check the wiring between HMI and I/0 Board

#50

Bkbd com err

Please check electrical connection and ground.

#51

Parameter error

Please contact Unity at 1-800-484-3013

#52

Program error

Please contact Unity at 1-800-484-3013

#53

Controller failure

Please contact Unity at 1-800-484-3013

Содержание UTS29
















































Результаты поиска

Содержание UTS29

Отзывы:

UNITY LAUNDRY SYSTEMS UTS29, Руководство пользователя, Страница: 36 / 49

Результаты поиска

Содержание UTS29

Отзывы: