Unitronics Vision OPLCV350-J-T2 Скачать руководство пользователя страница 11

Страница: 11 / 11

Vision™ OPLC™

Opening the Controller

Before performing these actions, touch a grounded object to discharge any electrostatic charge.

Avoid touching the PCB board directly. Hold the PCB board by its connectors.

1. Turn off the power supply, disconnect, and dismount the controller.

2. The back cover of the controller comprises 4 screws, located in the corners.

Remove the screws, and pull off the back cover.

Changing I/O Settings

After opening the controller and exposing the I/O board, you can change the jumper settings according
to the table shown above.

Changing Communication Settings (

V130/V350/V130J/V350J Only)

1. To access the communication jumpers, hold the I/O PCB board by its top and bottom connectors

and steadily pull the board off.

2. Locate the jumpers, and then change the settings as required, according to the jumpers’ settings

shown on page 10.

Closing the Controller

1. Gently replace the board. Make certain that the pins fit correctly into their matching receptacle.

Do not force the board into place; doing so may damage the controller.

2. Replace the back cover of the controller and fasten the corner screws.

Note that you must replace the back cover securely before powering up the controller.

Samara

tel. +7 846 273 95 85

[email protected]

Yekaterinburg

tel. +7 343 287 19 19

[email protected]

St. Petersburg

tel. +7 812 327 3752

[email protected]

Moscow

tel. +7 495 641 1616

[email protected]

Helsinki

tel. +358 9 540 4940

[email protected]

Vilnius

tel. +370 5 215 1646

[email protected]

Riga

tel. +371 6738 1617

[email protected]

Мinsk

tel. +375 17 200 0876

[email protected]

Tallinn

tel. +372 668 4500

[email protected]

Кiev

tel. +38 044 495 33 40

[email protected]

Содержание Vision OPLCV350-J-T2












Результаты поиска

Содержание Vision OPLCV350-J-T2

Отзывы:

Похожие инструкции для Vision OPLCV350-J-T2

Бренды по названию

Популярные бренды

Unitronics Vision OPLCV350-J-T2, Руководство по установке

Результаты поиска

Содержание Vision OPLCV350-J-T2

Отзывы:

Похожие инструкции для Vision OPLCV350-J-T2

Бренды по названию

Популярные бренды