Unitronics Vision 230 Скачать руководство пользователя страница 9

Страница: 9 / 9

Installation Guide

CANbus

121

terminating

resistor

121

terminating

resistor

Circuit

protection

device

24V Power

Supply

-V

These controllers comprise a CANbus port. Use this

to create a decentralized control network using one

of the following CAN protocols:



CANopen: 127 controllers or external

devices



Unitronics’ proprietary UniCAN: 60

controllers, (512 data bytes per scan)

The CANbus port is galvanically isolated.

CANbus Wiring

Use twisted-pair cable. DeviceNet® thick shielded

twisted pair cable is recommended.
Network terminators: These are supplied with

the controller. Place terminators at each end of the

CANbus network.

Resist

ance must be set to 1%, 121Ω, 1/4W.

Connect ground signal to the earth at only one

point, near the power supply.
The network power supply need not be at the end of

the network.

CANbus Connector

Samara

tel. +7 846 273 95 85

[email protected]

Yekaterinburg

tel. +7 343 287 19 19

[email protected]

St. Petersburg

tel. +7 812 327 3752

[email protected]

Moscow

tel. +7 495 641 1616

[email protected]

Helsinki

tel. +358 9 540 4940

[email protected]

Vilnius

tel. +370 5 215 1646

[email protected]

Riga

tel. +371 6738 1617

[email protected]

Мinsk

tel. +375 17 200 0876

[email protected]

Tallinn

tel. +372 668 4500

[email protected]

Кiev

tel. +38 044 495 33 40

[email protected]

Содержание Vision 230










Результаты поиска

Содержание Vision 230

Отзывы:

Похожие инструкции для Vision 230

Бренды по названию

Популярные бренды

Unitronics Vision 230, Руководство по установке

Результаты поиска

Содержание Vision 230

Отзывы:

Похожие инструкции для Vision 230

Бренды по названию

Популярные бренды