Unitronics Samba SM35-J-TA22 Скачать руководство пользователя страница 11

Страница: 11 / 11

Samba™ PLC+ HMI

Changing I/O Settings

The I/O board of the controller is now

exposed, enabling you to change

I/O settings (module dependent) according to

the jumpers setting above.

Note: Photo is for illustration purposes only.
(Using SM70)

Closing the Controller

Replace the back cover of the controller and fasten the corner screws.

Note that you must replace the back cover securely before powering up the controller.

FINLAND

[email protected]

www.klinkmann.fi

BELARUS

[email protected]

www.klinkmann.by

RUSSIA

[email protected]

www.klinkmann.ru

LATVIA

[email protected]

www.klinkmann.lv

LITHUANIA

[email protected]

www.klinkmann.lt

ESTONIA

[email protected]

www.klinkmann.ee

UKRAINE

[email protected]

www.klinkmann.com.ua

KAZAKHSTAN

[email protected]

www.klinkmann.kz

Содержание Samba SM35-J-TA22












Результаты поиска

Содержание Samba SM35-J-TA22

Отзывы:

Похожие инструкции для Samba SM35-J-TA22

Бренды по названию

Популярные бренды

Unitronics Samba SM35-J-TA22, Руководство по установке

Результаты поиска

Содержание Samba SM35-J-TA22

Отзывы:

Похожие инструкции для Samba SM35-J-TA22

Бренды по названию

Популярные бренды