Unitronics IO-LC1 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 12

background image

IO-LC1, IO-LC3

I / O E x p a n s i o n M o d u l e s

4/04

6

Unitronics Industrial Automation

Loadcell Inputs

Use 6 or 4 wire shielded cable (6 wire is recommended).

The cable shield should be connected ONLY to the Loadcell chassis. The shield at the other end of the
cable should be left unconnected.

Refer to the figures below for wiring guidelines.

6 wire Loadcell wiring

4 wire Loadcell wiring

«
...
4
5
6
7
8
...
»

Содержание IO-LC1













Отзывы:

Нет отзывов

Похожие инструкции для IO-LC1

ControlMaster CM15

Бренд: ABB Страницы: 28

Бренд: ABB Страницы: 139

Бренд: ABB Страницы: 28

Бренд: ABB Страницы: 59

Бренд: Nelsen Corporation Страницы: 16

Бренд: National Instruments Страницы: 34

Бренд: OmarLift Страницы: 14

Бренд: E-fly Страницы: 16

Бренд: BADODOSECURITY Страницы: 8

Бренд: Lawler Страницы: 6

Бренд: Data Aire Страницы: 28

Бренд: Fancom Страницы: 31

Бренд: 3M Страницы: 90

ESD-5550 Series

Бренд: GAC Страницы: 12

Бренд: Pando Страницы: 43

Бренд: Yealink Страницы: 8

Бренд: Parker Страницы: 38

Бренд: Parker Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды