4 / 4
P/N 146668999-
1 • REV B • ISS 27FEB18
Programming control panels
For outdoor applications it is recommended to use the wireless
detector as a pre-alarm device. Refer to the specific control
panel manuals for details on programming.
Walk test & settling time
Allow 3 minutes for the electronics to settle when power is
applied before commencing the walk test.
The walk test mode starts as soon as either or both tamper
switches are opened. In walk test mode the red LED (figure 10)
is activated. Walk test mode remains active until both tamper
switches are closed i.e. the detector is securely mounted to the
wall and the cover is closed. When both switches have been
closed a 5 minute time will start. After 5 minutes of both
switches being closed, the walk test will finish irrespective of
any detections. Opening either of the tamper switches at any
time will reset the 5 minute count timer.
Whilst in walk test mode the red detection LED will light each
time the wireless detector detects your presence.
Note:
When you conduct a walk test, make sure that the front
cover is in place. Do not conduct walk tests with the cover
removed.
The range of the detector increases without the protective front
cover. Therefore the front cover must be fitted to establish the
correct beam pattern. Pan and tilt the lens module over the
field of view to obtain the correct coverage area.
Specifications
Coverage
14° to 70° detection angle,
15 m x 13 m coverage max.
Adjustment
90° pan, 45° tilt
Fresnel lens
20 zones for each detection element, which
can be masked with the curtain sliders
Customised optics
Double silicon shielded quad element
eliminates 50,000 Lux of white light
LED
Red: Walk test indicator
Batteries
2x 3 V CR123 (up to 3 years)*
3x 3 V CR123 (up to 5 years)*
Current
50 μA
Wireless operating
frequency
433 MHz
Maximum power
output
≤10 dBm
Pulse count
1 or 2
Temperature
compensation
Analogue (thermistor) and digital sensitivity
adjustment
Control
Digital microprocessor with non-volatile
memory
Walk test
Output test mode with LED indication.
Operating temperature
−25° to +65°C
Housing
High impact ABS plastic with HDPE cover,
UV stabilised
Dimensions W x H x D
70 mm x 120 mm x 95 mm
Weight
218 g net, 351 g gross
Mounting height
Variable up to 6 m.
Optimum height 3 m for full range
Regulatory information
Manufacturer
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092,
USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Certification
Environmental
class
IP65
Warnings and
Disclaimers
These products are intended for sale to, and
installation by, an experienced security
professional. UTC Fire & Security cannot provide
any assurance that any person or entity buying its
products, including any “authorized dealer,” is
properly trained or experienced to correctly install
security related products.
For more information on product warnings, refer
to firesecurityproducts.com/policy/product-
warning/ or scan the code.
European Union
directives
UTC Fire & Security hereby declares that this
device is in compliance with the applicable
requirements and provisions of all applicable
rules and regulations, including but not limited to
the Directive 2014/53/EU. For more information
see: https://www.utcfssecurityproducts.eu/
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.utcfssecurityproducts.eu/recycle/.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific
battery information. The battery is marked with
this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to
your supplier or to a designated collection point.
For more information see:
www.utcfssecurityproducts.eu/recycle/.
Contact information
www.utcfireandsecurity.com or www.interlogix.com
For customer support, see www.interlogix.com/customer-
support
