United CoolAir VertiCool CLASSIC Скачать руководство пользователя страница 28

Страница: 28 / 40

Installation, Operation and Maintenance Manual

VertiCool Classic

Subject to change without notice.

20.10-IM (0617)

Limited Warranty for Hermetic Compressors

United CoolAir warrants the hermetic compressor in this

product to be free from defects in factory workmanship and

material under normal use and service and will, at its option,

repair or replace the hermetic compressor if it proves to

have such defects within a period of five (5) years from the

date of product installation� This warranty extends only to

the original consumer purchaser in accordance with the then

current Terms and Conditions and is non-transferable� If a

United CoolAir unit is matched with another manufacturers

unit the compressor warranty is limited to 1 year form the

date of product installation�
For this warranty to apply, the product must be installed

according to United CoolAir recommendations and

specifications, and in accordance with all local, state,

national and provincial codes� The product must not be

moved from its original place of installation� The replacement

part assumes the unused portion of this warranty�
This limited warranty applies only to products installed in the

continental United States, Alaska, Hawaii and Canada�

Exclusions

This Limited Warranty does not cover any:

Shipping, labor or material charges�

Damages resulting from transportation, installation or

servicing�

Damages resulting from accident, abuse, fire, flood,

alteration or acts of God�

Tampering with, altering, defacing or removing the

product serial number will serve to void this warranty�

Damages resulting from use of the product in a

corrosive atmosphere (such as concentrations of acids

or halogenated hydrocarbons)�

Damages resulting from inadequacy or interruption of

electrical service, improper voltage conditions, blown

fuses, or other like circumstances�

Cleaning or replacement of filters or belts.

Damages resulting from failure to properly and

regularly clean air and/or water side of condenser and

evaporator�

Damages resulting from: (I) freezing of condenser

water or condensate; (II) use of corrosive water; (III)

fouling or restriction of the air/water circuit by foreign

material or like causes�

10.

Damages resulting from operation with inadequate or

interrupted supply of air or water�

11.

Damages resulting from use of components or

accessories not approved by United CoolAir�

12.

This warranty does not apply to the installation,

plumbing and wiring not integral to the product�

13.

Damages resulting from improper application or sizing�

This warranty is in lieu of all other warranties, expressed or

implied, including the implied warranties of merchantability

and fitness for a particular purpose.
Some states (provinces) do not allow the disclaimer of

implied warranty, so that the above disclaimer may not apply

to you�
Some states (provinces) allow only a partial limitation on

implied warranties to limit the duration of implied warranties

to the duration of the express warranty� In such states

(provinces), the duration of implied warranties is hereby

expressly limited to the duration of the express warranty on

the face hereof�
In no event, whether as a result of breach of warranty or

contract, tort (including negligence) strict liability or otherwise,

shall United CoolAir be liable for special, incidental, or

consequential damages, including but not limited to loss

of use of the equipment or associated equipment, lost

revenues or profits, cost of substitute equipment or cost of

fuel or electricity� The above limitations shall inure to the

benefit of United CoolAir’s suppliers and subcontractors.

The above limitation on consequential damages shall not

apply to injuries to persons in the case of consumer goods�
Some states (provinces) do not allow the exclusion or

limitation of liability for consequential damages, or for strict

liability in tort, so that the above exclusions and limitations

may not apply to you�
United CoolAir does not assume, or authorize any other

person to assume for United CoolAir, any other liability for

the sale of this product�
This warranty gives you specific legal rights. You may also

have other rights which vary from state to state (province to

province)�

To obtain warranty service

Contact the installing or servicing contractor with the details

of the problem� Provide the model number, serial number

and date of installation� Warranty requests directed to the

factory will be referred back through the local distribution

network�

Model: ______________

Serial Number: _______________

Date of Installation: ________

Содержание VertiCool CLASSIC









































Результаты поиска

Содержание VertiCool CLASSIC

Отзывы:

Похожие инструкции для VertiCool CLASSIC

Бренды по названию

Популярные бренды

United CoolAir VertiCool CLASSIC, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание VertiCool CLASSIC

Отзывы:

Похожие инструкции для VertiCool CLASSIC

Бренды по названию

Популярные бренды