Copyright 2008 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
34
Copyright 2008 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
35
STEP 2 – Enter flash font program mode:
Send <ESC> <‘D’> <‘A’> <0> to select ASCII flash font upload and wait for the printer
to deactivate the CTS line. For the 2500/1500 or the 3750 printers the last number can
be anything between 0..7
STEP 3 – Wait for the printer ready indicators:
Wait for the printer to reactivated the CTS line and transmitted the character ‘?’
STEP 4 – Load new the character:
Upload the user defined ASCII ‘A’ character.
The basic command format and an actual command string are shown below:
<ESC> <‘D’> <ASCII TABLE 0> <Character Code> <46 byte dot matrix data> //for
the 2500/1500 or 3750 the table # does not matter as long as you specified the bank
number.
<ESC> <‘D’> <0> <0x41>
<0x00> <0x00> <0x00> <0x40> <0x00> <0xE0> <0x00> <0xA0>
<0x01> <0xB0> <0x01> <0x10> <0x01> <0x10> <0x01> <0x10>
<0x01> <0x10> <0x03> <0x18> <0x03> <0x18> <0x03> <0xF8>
<0x03> <0xF8> <0x02> <0x08> <0x02> <0x08> <0x06> <0x0C>
<0x06> <0x0C> <0x04> <0x04> <0x04> <0x04> <0x04> <0x04>
<0x0E> <0x0E> <0x0E> <0x0E> <0x00> <0x00>
STEP 5 – Save the modified character to flash:
Sending the command <ESC>-‘D’- <0xFF> {CHR$(27) + ‘D’ + CHR$(255)}, copies
the revised character to the printer flash location.
The printer will transmit the character ‘D’ and then proceed to save the fonts to flash
memory. THE PRINTER POWER MUST REMAIN ACTIVE AT THIS TIME.
STEP 6 – Cycle the printer power:
Once the fonts have been saved into flash memory, the printer will transmit the
character ‘!’.
At this time, the printer will transmit an ‘X’ every 500 milliseconds.
To ensure optimal operation of the printer, remove the battery cartridge from the
printer for several seconds. Replace the battery cartridge and the new fonts will be
ready for use.
To ensure optimal operation of the printer, remove the battery cartridge from the
printer for several seconds. Replace the battery cartridge and the new fonts will be
ready for use.
A.2.0 Graphic Logo Print Option
The following paragraphs summarize the operation of the Graphic Logo feature for the
Unitech MP200 printer. The Graphic Logo feature enables the storage of formatted
Bitmap file in nonvolatile memory. Up to eight memory sectors of up to 8,544 bytes
each, are reserved to store Graphic Logo in the printer upon receipt of a Graphic
Logo print command, the Graphic Logo data is sent to the printer. The feature enables
printing of a stored graphic image as part of a receipt.
A.2.1 Specification
Printer
Number of
Logos
Bytes per
logo
Dot lines
per logo
Dots per line
MP200
8 (FLASH)
8,544
178
384
Table A.6 – Printer Specifications
A.2.2 Graphic Logo Operation MP200
•
On initial power-up, the Host application selects the Flash Logo Mode by
sending the command String:
<ESC - D – L-n>.
Printer responds by sending? Character to the host application indicating that
the Flash Logo Mode is enabled.
•
The Host application selects the Graphic Logo record mode by sending the load
command:
<ESC - L - G - n>.
•
Once printer is placed in record mode, the Graphic Logo is downloaded using
8-bit graphic command:
<ESC> <V> <0x01> <0x00> <48 bytes of Graphic data>
•
The Graphic Logo record mode is terminated automatically after receiving 178
graphic lines, or upon receiving the Graphic Logo record terminate command
string.
ESC - L - G - < 0xff >
•
Printer saves the received Logo data in flash and sends D!X characters to the
host, indicating that logo data was saved.
The printer power must be cycled to return to normal operating mode.
