![background image](http://html.mh-extra.com/html/unitec/csr-150/csr-150_owners-manual-and-operating-instructions_844164004.webp)
OPERATIONAL AND SAFETY INSTRUCTIONS
- continued
♦
Check the area to be cut; be sure it is free of all loose debris, and be
sure no-one is standing in the cut line.
♦
Use only CS Unitec-approved diamond blades that have been rated
for this saw’s r.p.m. Inspect all blades for damage before use.
Do
not
under any circumstance
use a bent or warped blade, or a blade
with a missing segment, as an out-of-balance condition could result
in the blade coming apart.
♦
Always check arbor bearing for end play.
♦
Check that the guard is secure and undamaged.
♦
Check to see that all nuts and bolts are tight.
♦
Never cut material for which the blade is not designed.
♦
Do not start, run or operate the equipment near combustible
materials.
ASSEMBLY INSTRUCTIONS
1.
Slip handle assembly over the two 3/4” handle pins. Tighten the two
3/8” set bolts to secure the handle.
2.
Connect height control jack assembly on the handle to the top of the
motor mount with the 3/8”x 3/4” bolt supplied. Raise the jack to full
up position to install blade.
3.
Connect the air hose from the center of the handle to the in-line oiler
on the motor. Fill the oiler with CS Unitec Air Tool Lubricant.
4.
Connect the clear water hose from the handle assembly to the water
spray head on top of the guard.
5.
Install blade. This saw rotates in a clockwise direction when viewed
from the right side of the saw. Be careful that the arrow on the blade
goes in the same (clockwise) direction. Place blade on the hub of
the inner flange and then secure the outer flange and 5/8”-11 left-
hand nut. Use the two wrenches supplied to tighten the blade, and
spin the blade by hand to see that it is running true. Check that all
nuts and bolts are tight.
- 3 -
OPERATIONAL AND SAFETY INSTRUCTIONS
- continued
♦
Check the area to be cut; be sure it is free of all loose debris, and be
sure no-one is standing in the cut line.
♦
Use only CS Unitec-approved diamond blades that have been rated
for this saw’s r.p.m. Inspect all blades for damage before use.
Do
not
under any circumstance
use a bent or warped blade, or a blade
with a missing segment, as an out-of-balance condition could result
in the blade coming apart.
♦
Always check arbor bearing for end play.
♦
Check that the guard is secure and undamaged.
♦
Check to see that all nuts and bolts are tight.
♦
Never cut material for which the blade is not designed.
♦
Do not start, run or operate the equipment near combustible
materials.
ASSEMBLY INSTRUCTIONS
1.
Slip handle assembly over the two 3/4” handle pins. Tighten the two
3/8” set bolts to secure the handle.
2.
Connect height control jack assembly on the handle to the top of the
motor mount with the 3/8”x 3/4” bolt supplied. Raise the jack to full
up position to install blade.
3.
Connect the air hose from the center of the handle to the in-line oiler
on the motor. Fill the oiler with CS Unitec Air Tool Lubricant.
4.
Connect the clear water hose from the handle assembly to the water
spray head on top of the guard.
5.
Install blade. This saw rotates in a clockwise direction when viewed
from the right side of the saw. Be careful that the arrow on the blade
goes in the same (clockwise) direction. Place blade on the hub of
the inner flange and then secure the outer flange and 5/8”-11 left-
hand nut. Use the two wrenches supplied to tighten the blade, and
spin the blade by hand to see that it is running true. Check that all
nuts and bolts are tight.
- 3 -