Unique PRESTIGE UGP-20V PC1 B Скачать руководство пользователя страница 44

Страница: 44 / 55

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

POSSIBLE FIX

Surface burners

do not light.

Surface control has not been com-

pletely turned to the ON position.

Push in and turn control to the ON position

until burner ignites, then turn control to de-

sired flame setting.

Burner ports are clogged.

Use a small gauge wire or needle to open

ports.

Burners not positioned properly.

Verify that the burners are positioned prop-

erly on the orifice hoods and the burners are

sitting flat on the burner support with tabs

engaged in slots.

Range not set for appropriate gas

input.

See range conversion section of installation

manual.

Burners won’t light due to power

failure.

Light burners manually.

Range power cord is disconnected

from the outlet.

Be sure power cord is plugged into grounded

outlet.

Flame burns half-

way round.

Burner ports are clogged.

Use a small gauge wire or needle to open

ports.

Moisture is present after cleaning.

Lightly fan the flame and allow burner to oper-

ate until flame is full. OR dry burners thor-

oughly following instructions in range “Clean-

ing” section.

Range is not set for appropriate gas

input.

See range conversion section of installation

manual.

Flame is orange.

Dust particles in main line.

Allow burner to operate for a few minutes

until flame turns blue.

Range is not set for appropriate gas

input.

See range conversion section of installation

manual.

Oven light does

not work.

Burned out or loose bulb

Tighten or replace oven light bulb.

Oven or broiler

does not heat.

Range is not set for

appropriate gas input.

See range conversion section of installation

manual

Temperature control not set properly. Make sure temperature control is set at de-

sired temperature.

Burners will not light due to power

failure.

Light burners manually.

House fuse has blown or circuit

breaker has tripped.

Check/reset circuit breaker and/or replace

fuse. Do not increase fuse capacity. If the

problem is a circuit overload, have it corrected

by a qualified electrician.

Range cord is disconnected from

outlet.

Be sure the power cord is plugged into a

grounded outlet.

Oven capillary bulb not positioned properly.

Verify that capillary bulb is snapped in clips

straight and not touching sides or coated with oven cleaner or food.

Temperature control not set properly.

Make sure the temperature control knob is set at the desired temperature.

Improper use of foil.

Keep foil clear of holes in oven bottom and off of oven sides.

Vent blocked.

Keep vent on backguard clear.

Range not set for appropriate gas input.

See range conversion section of installation manual.

Содержание PRESTIGE UGP-20V PC1 B
























































Результаты поиска

Содержание PRESTIGE UGP-20V PC1 B

Отзывы:

Похожие инструкции для PRESTIGE UGP-20V PC1 B

Бренды по названию

Популярные бренды

Unique PRESTIGE UGP-20V PC1 B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PRESTIGE UGP-20V PC1 B

Отзывы:

Похожие инструкции для PRESTIGE UGP-20V PC1 B

Бренды по названию

Популярные бренды