background image

U S E R   I N S T R U C T I O N S

page 4

Setup   

    Rear Panel   Operating Instructions   

Stereo Operation 

Parallel Mono Operation 

Mono Bridge Operation

   Specifications

Front Panel

1. Clip LED 

The clip LED indicates the exact clipping point, regardless of the 

mains voltage and or the connected load. The symmetrical supply voltages of 
the power pack of an amplifier limit its output power. If amplifier is overdriven by 
a too high input signal, the output signal tries to exceed the value of the supply 
voltage. At this moment, the amplifiers “clip”. this results in a dangerous situation 
for the connected loudspeakers. The peak limiter, if switched on, intervenes here 
by automatically limiting the output signal-this is indicated by the clip led of the 
channel in question.

2. Signal LED

 - The signal LED indicates a -30db point relative to the clipping 

point, regardless of the mains voltage and the connected load. This LED gives 
the user a better control of the remaining headroom of a channel or a complete 
system.

3. Power LED

 - When you have switched on the amplifier, the ON LED indicates 

the power is being supplied to the channel. If none of the LED light up once the 
appliance has been switched on, this might be due to the following fault: no 
power supply from the mains outlet. Please check that the appliance has been 
plugged in properly and check that power is being supplied from the mains 
outlet.

4. Bridge LED

 - The bridge LED will light when you have set the rear panel MODE 

SWITCH 

14

) 

for mono bridge operation. Always make sure that this switch is 

in the correct position and that all speaker connections have been made 
correctly for the mode of operation you wish to use before powering up the 
amplifier.

5. Stereo LED

 - The stereo LED will light when you have set the rear panel MODE 

SWITCH 

14

) 

for stereo operation. Always make sure that this switch is in the 

correct position and that all speaker connections have been made correctly for 
the mode of operation you wish to use before powering up the amplifier. 

6. Parallel LED

 - The parallel LED will light when you have set the rear panel 

MODE SWITCH

14

) 

for parallel mono operation. Always make sure that this 

switch is in the correct position and that all speaker connections have been 
made correctly for the mode of operation you wish to use before powering up the 
amplifier.

7. Power Switch

 - Turns the unit on and off.

8. Level controls

 - Establish the input levels required for each channel. only the 

channel 1 level control works in mono Bridge mode.

PS-3000/PS-4000/PS-5000

UNiKA

 

UNiK A

1 2 3

5 6

1

2

3

7

8

PS-5000

4

Содержание PS-3000













Отзывы: