unigreen
23
We recommend having the normal UNIGREEN assistance service available from our reseller
perform any repairs or contact a specialised workshop. During all of the repairs, in particular
when welding, the machine and the circuit must be clean of any residues of chemical product.
If the machine has to be lifted (for example to change a wheel) follow the instructions in point
4.3 of the present handbook.
Also make sure the machine is stopped, connected to the tractor, and use the relevant chocks
to block the wheel still on the ground.
If you use a jack (manual or hydraulic) make sure you use a jack that is suitable for the frame
so it can’t slip and put it in the right position. The jack must be placed under the main frame of
the machine near the wheel to change. Make sure the ground is compact: if necessary use
wooden beams or other sufficiently resistant material to broaden the supporting base of the
jack.
8.5
STORAGE IN A WAREHOUSE AND TRANSPORTATION
The sprayer must be kept in a closed place away from excessive humidity and protected from
frost. Especially if electrical pressure regulators, electrical motors, a spraying computer or
similar components are fitted.
Before storing the machine, after you have washed it, apply a light coat of oil.
If the temperature might drop to below zero, drain any residual liquid or add roughly 0.5 L of
normal antifreeze for auto vehicles.
To transport the machine follow the instructions in point 4.3 of the present handbook.
8.6
PUTTING BACK INTO SERVICE AFTER WINTER LAYUP
Before using the machine again after a long period of inactivity you should perform some
general checks, following the instructions in point 4.2 and drain any antifreeze.
Never start the shaft of the pump if you think there may by ice inside. To check this,
make sure you can turn the shaft by hand without connecting it to the tractor.
After you have connected the machine to the tractor (see point 4.4) following the instructions
in the present user’s handbook and in the enclosures of the pump, pressure regulator and
accessories.
8.7
DEMOLITION AND DISPOSAL
When the sprayer will be put out of service you should wash it with great care to remove any
residues of chemical product, follow the instructions in point 4.13 of the present handbook.
ATTENTION: It is necessary to adopt appropriate Individual Protection Devices in manipulating
waste.
The disposal of waste deriving from the demolition of the machine must be carried out
respecting the environment, avoiding soil, air and water pollution.
Local legislation in force in the matter must be respected in any case.
Remember that waste is understood as any substance or object that enters into the categories
shown in attachment A in part IV of Legislative Decree 152/2006, that the holder has
destroyed, has decided or is obliged to destroy.
Waste deriving from the demolition of the machine is classifiable as special waste.
8.7.1 MATERIALS FOR DEMOLITION
Non-dangerous special waste is that which can be recovered, according to the February 1998
Ministerial Decree:
·
Iron, aluminium, stainless steel and copper materials
·
Plastic materials
·
Electronic cards
·
Hydraulic oil
·
Electrical plant
8.7.2 INDICATIONS FOR A SUITABLE TREATMENT OF WASTE
The Correct management of special waste envisages:
-
stocking in suitable places, avoiding mixing dangerous waste with the non-dangerous.
-
ensuring that authorised carriers and receivers carry out its transport and disposal/
recovery.
Transport of one's waste to authorised collection centres is allowed exclusively if you are
enrolled in the Environmental Management Register.
8.7.3 ELECTRICAL AND ELECTRONIC APPARATUS WASTE (EEAW)
The Italian government has adopted the European Parliament directives in the matter of the
disposal of electrical and electronic waste (EEAW) (2002/95/CE and 2003/108/CE Directives)
with Legislative Decree n° 151,July 25 2005).
The measures: in particular, the decree established measures and procedures aimed at:
a) forestalling the production of EEAW;
b) promoting the re-use, recycling and other forms of EEAW recovery, in order to reduce the
quantity to send for disposal;
c) improving, in terms of the environment, the actions of the subjects who participate in the
life-cycle of these apparatuses (producers, distributors, consumers and operators directly
involved in the treatment of EEAW);
