background image

Contents

Read the instructions carefully.

Check all cutting equipment is all correctly fitted and
adjusted.

Refuel and start the saw. Check carburetor settings.

Do not use the saw until sufficient chain oil has
reached the chain.

Before Using A New Saw

WARNING!

Under no circumstances may the design of the
machine be modified without the permission of
the manufacturer. Always use genuine spare
parts/accessories. Non Autorized modifications
and/or accessories can result in serious personl
injury or the death of the operator or others.

The warranty does not cover damage or liability
caused by the non-authorized accessories or
replacement parts.

WARNING!

The engine exhaust from this product contains
chemicals known to the state of California to
cause cancer, birth defects or other reproductive
harm.
The warranty does not cover damage or liability
caused by the non-authorized accessories or
replacement parts.

Congratulations....

On your purchase of the worlds finest high
performance, ventilation saw.  This saw has
been designed to meet the rugged require-
ments of the fire service.  To ensure maximuim
performance and reliability this saw’s carburator
should be set for the altitude it is intended to
run at, and the R.P.M. should be set at 13,500.
This can be achieved through the dealer you
purchased the saw from or at any authorized
Unifire dealer.  If you should need assistance in
locating the nearest dealer please call 1-800-
745-3282 and ask for our customer service
deptartment.  We would sincerely like to thank
you for your purchase of Unifire’s ventilation
saw, one of the team products.

Safety Instructions
Personal protective equipment
General Safety precations
Avoiding Kickback
Cutting Equipment

What is What
Saw parts diagram

Assembly
Mounting guide bar and chain

Fuel Handling
Fuel mix
Fueling

Start and Stop
Procedures and hints

Maintenance
Air Filter
Spark Plug
Tensioning the recoil spring
Changing recoil spring
Carburetor
Daily maintenace
Weekly maintenance
Monthly maintenance

Depth Guage Instructions

CONTENTS

3924 E. Trent Ave.

Spokane, WA 99202

Phone: (509)535-7746

Fax: (509)535-9064

1-800-745-3282

www.unifireusa.com

Page 1

Содержание Saw












Отзывы: