unicraft PG-I SE Series Скачать руководство пользователя страница 5

Safety

PG-I SE Series | Version 1.04

5

The qualifications of the personnel for the different tasks 
are mentioned below:

Operator

The operator is instructed by the operating company 
about the assigned tasks and possible risks in case of 
improper behaviour. Any tasks which need to be perfor-
med beyond the operation if it is indicated in these in-
structions and if the operating company expressively 
commissioned the operator.

Qualified personnel

Due to their professional training, knowledge and experi-
ence as well as their knowledge of relevant regulations 
the specialist staff is able to perform the assigned tasks 
and to recognise and avoid any possible dangers them-
selves.

Manufacturer

Certain works may only be performed by specialist per-
sonnel of the manufacturer. Other personnel is not au-
thorized to perform these works. Please contact our cus-
tomer service for the execution of all arising work.

2.4 Personal protective equipment

The personal protective equipment serves to protect per-
sons against impairments of safety and health while 
working. The staff member has to wear personal protec-
tive equipment while performing different tasks on and 
with the machine which are indicated in the individual 
paragraphs of these instructions.

The personal protective equipment is explained in the 
following paragraph:

2.5 General safety instructions

- Never operate the generator in closed rooms which 

do not have sufficient ventilation. The engine pro-
duces carbon monoxide and other harmful gases 
that are harmful to the health of the people who 
breathe them. If you feel dizzy or have a fainting 
spell, get out into the fresh air immediately. For this 
reason, adequate ventilation must be ensured. 
Combustion fumes must be led out of the engine 
room or the working area of the personnel via pipes 
and exhaust systems. It is recommended to install a 
CO alarm device!

-  Only operate the generator outdoors. DO NOT allow 

exhaust gases to enter a closed area through 
windows, doors, vents or other openings.

-  Operate the generator only on horizontal surfaces to 

ensure optimum flow of oil and fuel to the motor. If 
operation on horizontal surfaces is not possible, the 
user must install suitable mounting and levelling de-
vices to ensure safe stand the generator.

- Always wear firm and dry shoes while working on the 

generator. Never work barefoot!

- Do not operate the generator if you are tired or under 

the influence of drugs, alcohol or medication.

-  Keep children away from the running generator at 

all times and in any case; note that the switched off 
motor will remain hot for some time. At the exhaust, 
the exhaust pipes and at the engine the increased 
temperatures last the longest. Touching them can 
cause severe burns.

-  Do not carry out any checks or maintenance work 

on the generator in operation; switch off the motor in 
any case. NEVER touch blank wires or sockets.

- DO NOT use a damaged or frayed electrical cable.

- DO NOT operate the generator in the rain.

- Use an RCD in humid areas and areas containing 

conductive material.

-  Refueling with fuel and topping up oil must be done 

with the engine switched off (5 minutes cooling 
time). It must be noted that the engine will maintain 
its high temperature for a period of time after it has 
been switched off.

- Allow the machine to cool before touching it. A mini-

mum distance of 90 cm should be maintained on all 
sides to ensure adequate cooling. Keep at least 1.5 
m away from flammable materials.

- When unscrewing the tank cap, open it slowly to 

slowly reduce any existing pressure. 

- Keep fuel away from sparks, open fire, ignition fla-

mes, heat and other sources of ignition.

- The functions and circuits of the generator should be 

known: Unexperienced persons should not be allo-
wed to use the generator.

Protective goggles

The protective goggles serve to protect the eyes 
against parts flying off.

Protective gloves

The protective gloves serve to protect the hands 
against sharp components as well as against fric-
tion, abrasions or deep injuries. 

Safety boots

Safety boots protect the feet from being crushed, fall-
ing parts and slipping over on slippery ground 

Protective clothes

Protective clothes are made of a tightly fitted fabric 
without the protruding parts of low tear strength. 

Содержание PG-I SE Series







































Отзывы: