manualshive.com logo in svg

Unibloc-Pump LABTOP 200, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Unibloc-Pump LABTOP 200 Скачать руководство пользователя страница 36

            

        Page 37 of 41

1

3

4

5

6

7

10

11

12

13

16

14

15

21

17

18

20

30

29

28

27

26

25

24

23

22

2

19

9

8

CONTACT UNIBLOC-PUMP IF PART NUMBER IS NOT AVAILABLE

ITEM NO.

DESCRIPTION

PART NUMBER

QTY.

1

DOWEL PIN

 DPM5x14

2

2

M5x10 BUTTON HEAD SCREW

BHM5x10

2

3

OIL SEAL RETAINER

3640

1

4

FRONT OIL SEAL

4105

2

5

SHAFT O-RING (16mmx1mm)

4203

2

6

SHAFTS

---

2

7

FRONT BEARINGS

3750

2

8

FLAT HEAD BOLT

FHBM3x

6

8

9

SHIM

 PLATE

3646-075

4

10

BEARING HOUSING

3500

1

11

REAR BEARINGS

3750

2

12

SHAFT KEYFOR TIMING GEARS

4700

2

13

GEAR

3600

2

14

TAB WASHER FOR TIMING GEARS

4500

2

15

SLOTTED NUT FOR TIMING GEARS

4402

2

16

REAR COVER O-RING (3.237"x0.103" #152)

4201

1

ITEM NO.

DESCRIPTION

PART NUMBER

QTY.

17

BEARING HOUISNG COVER

3551

1

18

REAR OIL PLUG

4101

1

19

DRAIN PLUG

---

2

20

REAR OIL SEAL

4100

1

21

SHAFT KEY FOR DRIVE

4701

1

22

M8x25 HEX BOLT

4300

4

23

M6 DOME NUT

4400

4

24

ROTOR HOUSING COVER

3200

1

25

FRONT COVER O-RING (2.987"x0.103" #151)

4200

1

26

ROTOR BOLT O-RING (0.799"x0.103" #117)

4213

1

27

ROTOR BOLT

3352

2

28

ROTOR

---

2

29

ROTOR HOUSING STUD

---

4

30

ROTOR HOUISNG

---

1

BY

SCALE

APP'D

CHECKED

DRAWN

DATE

ALL DIMENSIONS IN MM, [IN]

SHEET 1 OF 2

DWG. NO.

06/09/15

JPZ

G805

3

REV. NO.

JUN. 21, 2021

UNIBLOC-PD PUMP PARTS LIST

200,250,275

SIZE

RELEASE DATE 

DWG. TITLE

THIS DRAWING AND ALL IDEAS INCORPORATED IN ITS  DESIGN IS THE EXCLUSIVE PROPERTY OF UNIBLOC  HYGIENIC TECHNOLOGIES, LLC.  ITS ACCEPTANCE  CONSTITUTES AN AGREEMENT THAT IT SHALL BE TREATED  AS A CONFIDENTIAL DOCUMENT USED FOR NO OTHER  PURPOSE THAN TO AID IN ITS CONSTRUCTION, THAT IT IS  TO BE RETURNED UPON REQUEST, AND THAT IT IS NOT TO  BE DISCLOSED OR COPIED EXCEPT AS AUTHORIZED IN  WRITING BY UNIBLOC HYGIENIC TECHNOLOGIES, LLC.

Содержание LABTOP 200










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды