manualshive.com logo in svg

Unibloc-Pump LABTOP 200, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Unibloc-Pump LABTOP 200 Скачать руководство пользователя страница 32

            

        Page 33 of 4

7.4.1 Digital Key Pad Operation 

 
Standard digital keypad (Figure 7.4.1.1) functions are explained below. 
 

 

Figure 7.4.1.1 

 

FWD

 

Initiates forward run.  If the pump is running in reverse when FWD is pressed, it will decelerate to zero 
speed, change direction, and accelerate to a preset speed.  

REV

 

Initiates reverse run.  If the pump is running in forward when REV is pressed, it will decelerate to zero 
speed, change direction, and accelerate to a preset speed.  

STOP

 

Decelerates at a preset rate to stop. 

UP

 

In stop mode this causes the running speed to increase in the display only.  The new speed may then be 
engaged by pressing FWD or REV.  In run mode pressing this key increases the speed up to a preset 
maximum.   

DOWN

 

In stop mode this causes the running speed to decrease in the display only.  The new speed may then 
be engaged by pressing FWD or REV.  In run mode pressing this key decreases the speed down to a 
preset minimum. 

ENTER

 

In stop or run modes pressing this key will store the selected frequency as the initial frequency when 
the unit is powered up.  The frequency is maintained until another frequency is entered. 

PROG 

In run mode, pressing this key will access Level 1 parameters for viewing  

 

 

 

only.  Holding SHIFT and then pressing PROG will access Level 2 for   

 

viewing only.   

 
 

7.4.2 Touch Screen Key Pad Operation 

 
Touch Screen keypad (Figure 7.4.2.1 & Figure 7.4.2.2) is available on select models of 

LABTOP

®

 

units.  After start up and 

information screens, the following base function keypad is shown.  Keypad functions are as follows: 
 

Содержание LABTOP 200










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды