Unibloc-Pump 54001010P20H6010T12E, Руководство по эксплуатации и обслуживанию

Страница: 39 / 53

UNIBLOC-PD Operation & Service Manual: PD200-576 39
5.3 Tools and Torque Requirements
Table 5.3.1 lists required tools and torque.
Description Tool Required Pump Model
200-0; 200; 250; 275 300; 350 400; 450 500/501;
550/551;
575/576
Front Cover Nut
#16
Wrench Size (mm)
Torque Settings (Nm)
Torque Setting (lbft)
6
10
7
13
15
11
17
30
22
19
50
37
Rotor Bolt
#14a
Socket Size (mm)
Torque Settings (Nm)
Torque Setting (lbft)
10 with part# 6006-2
20
15
13
35
25
17
70(110 for HP)
50(80 for HP)
19
165(250 for HP)
120(180 for HP)
Rotor Housing
Stud Nut #43
Wrench Size (mm)
Torque Settings (Nm)
Torque Setting (lbft)
10
8
6
13
8
6
17
20
15
19
40
30
Retainer Ring Bolt
#32
Key Size (mm)
Torque Settings (Nm)
Torque Setting (lbft)
N/A
N/A
N/A
5
Hand tight
Hand tight
5
Hand tight
Hand tight
5
Hand tight
Hand tight
Bearing housing
Cover Bolts
#18
Socket Size (mm)
Torque Settings (Nm)
Torque Setting (lbft)
13
20
15
10
15
11
10
15
11
17
40
30
Mechanical Seal
set screw
Key Size (mm)
Torque Settings (Nm)
Torque Setting (lbft)
N/A
N/A
N/A
2.5
Hand tight
Hand tight
2.5
Hand tight
Hand tight
3
Hand tight
Hand tight
Foot/Pedestal
Mounting Bolt
#19
Key Size (mm)
Torque Settings (Nm)
Torque Setting (lbft)
N/A
N/A
N/A
6
Hand tight
Hand tight
8
Hand tight
Hand tight
8
Hand tight
Hand tight
Rotating/Rotate/
Turn Shaft by
turning rotors bolt
#14a
Socket Size (mm)
Torque Settings (Nm)
Torque Setting (lbft)
10 with part# 6006-2
2
1.5
13
4
3
17
6
4.5
19
10
7.5
Shaft Guard Key Size (mm)
Torque Settings (Nm)
Torque Setting (lbft)
N/A
N/A
N/A
4
Hand tight
Hand tight
4
Hand tight
Hand tight
4
Hand tight
Hand tight
Oil Plug
#47b
Key Size (mm)
Torque Settings (Nm)
Torque Setting (lbft)
N/A
N/A
N/A
6.5
Hand tight
Hand tight
6.5
Hand tight
Hand tight
8
Hand tight
Hand tight
Table 5.3.1
5.3.1 Special Tools
There are only a few special tools needed to assemble the UNIBLOC in a safe and secure way. Please contact your pump supplier
for ordering.
1) Bearing housing series 200 (Model 200-0 to 275) requires a socket removal/installation tool. Part# 6006-2
2) A plastic spline assembly sleeve is highly recommended when installing the rotor housing.
UNIBLOC-PUMP can supply factory assembly sleeves.
Please contact your pump supplier. Model 300/350 (Part# 6210) Model 400/450 (Part# 6220)
Model 500/501 550/551 /575/576 (Part# 6230)