manualshive.com logo in svg

Uniblitz VincentAssociates VED24, Инструкция по эксплуатации

Поделиться
Скачать
Uniblitz VincentAssociates VED24 Скачать руководство пользователя страница 25

 

VED24 User Manual 

24

I/O

 

Considerations

 

The PULSE INPUT BNC is an Active Low input.  When a signal transitions from the high state 
to the low state, the shutter driver will be initiated and the shutter will transition.  Because this is 
an Active Low input, the controller can be triggered from a remote activate cable such as the 
optional 710R or the 710R/F. 
Be advised the SYNC OUTPUT is also designated as an Active High output.  These remote 
activate cables cannot be connected to any output. 

 

USB

 

Operation

 

The 

VED24 

can also be controlled via a serial command from a computer’s USB port 

(configured as a virtual COM port).  A USB cable is included with the controller.  Once the 
device is connected to a computer, in most instances, the driver for the USB interface will be 
installed.  If this connection does not occur, a USB driver program can be downloaded from: 
 

http://www.ftdichip.com/Drivers/CDM/CDM%20v2.12.04%20WHQL%20Certified.exe

 

This USB driver is also included on the Flash Drive which is included with your VED24 
controller.  In fact, in addition to the link above, the USB driver can be found on the same Flash 
Drive that this PDF User Manual is located.  Once communication is established, the shutter can 
be commanded to the open position by sending the ASCII ”@” symbol.  The shutter will close 
by sending a capital “A” symbol. See USB Commands in the “SPECIFICATION” section on 
page #27. 
Testing the communication can be accomplished with a terminal emulation program such as 
Termite 3.1, found at 

http://www.compuphase.com/software_termite.htm

. (Termite 3.1 is 

copyrighted software that is free for personal and commercial use. You may use it and distribute 
it without limitations. You may however not remove or conceal the copyright. There are no 
guarantees or warranties whatsoever; use it at your own risk.)

 

 

 

 

CAUTION 

Do not connect a 710R or 710R/F to the SYNC OUTPUT BNC.  This 
will damage the SYNC OUTPUT. 

Содержание VincentAssociates VED24




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды