manualshive.com logo in svg

UNI-T UT39E, Руководство по эксплуатации

Поделиться
Скачать
UNI-T UT39E Скачать руководство пользователя страница 19

 

19

Remark:

l

l
l
l

At 20A Range: For continuous measurement  10
seconds and interval not less than 15 minutes
Measurement voltage drop: Full range at 200mV.
Frequency reaponse: 40Hz~400Hz
Display effective value of sine wave (mean value
response).

E. Resistance Test

Range

200

Ω

2k

Ω

20k

Ω

2M

Ω

200M

Ω

Resolution

0.01

Ω

0.0001k

Ω

0.001k

Ω

0.0001M

Ω

0.01M

Ω

Accuracy

(0.5%+10)

(0.3%+1)

[5%(reading

-100)+10]

Overload Protection

250V rmss

Remark:

l

l

At 200M

Ω

 range, test lead is in short circuit, and it is

normal to display 100 digits. During measurement,
subtract the 100 digits from the reading.
When measuring at the range of 200

Ω

, short-circuit

the red and black test leads beforehand to display
the test lead’s resistance value.  Then use the
measured value minus this test lead’s resistance
value to obtain the correct tested resistance value.

Remark:

l

l

At 20A Range: For continuous measurement  10
seconds and interval not less than 15 minutes
Measurement voltage drop: Full range at 200mV.

D. AC Current

Range

2mA

200mA

20A

Resolution

0.0001mA

0.01mA

0.001A

Accuracy

(0.8%+10)

(1.2%+10)

(2.5%+10)

Overload Protection

0.315A. 250V fast

type fuse, 

φ

5 x 20mm

Un-Fused

Model UT39E: OPERATING MANUAL

Содержание UT39E

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды