UNI-T UPO1000CS Series Скачать руководство пользователя

Страница: 65 / 99

actual signal.

10.2 Acquisition Mode

To obtain a waveform from sampling points, press the ACQUIRE



sampling mode to select acquisition

mode.

(1) Normal Sampling

The signal is sampled and reconstructed with equal time intervals. For most waveforms, this mode

can perform the best display.

(2) Peak Sampling

The maximum and minimum values of the input signal are found at each sampling interval, and the

waveform is displayed these values. The oscilloscope can acquire and display a narrow pulse,

otherwise the narrow pulse might be missed in the normal mode. Noise might be enlarged in this

mode.

(3) High Resolution

The oscilloscope will averages the adjacent points of the sampled waveform and reduce random

noise from the input signal and generate smoother waveforms.

(4) Average

The oscilloscope obtains several waveforms to take the average, and display the final waveform.

This method can reduce random noise.

By changing the acquisition mode setting to observe the waveform changes. If the signal contains

large noise, when the average mode is not adopted and when the 32 times average mode is adopted,

the sampled waveform is shown in the following figure.

Waveform when the average mode is not adopted

waveform when the 32 times average mode

Note:

Average and high resolution uses different average methods. The former is multiple sampling

average, the latter is single sampling.

Pulse disappear

Содержание UPO1000CS Series




































































































Результаты поиска

Содержание UPO1000CS Series

Отзывы:

Похожие инструкции для UPO1000CS Series

Бренды по названию

Популярные бренды

UNI-T UPO1000CS Series, Руководство пользователя

Результаты поиска

Содержание UPO1000CS Series

Отзывы:

Похожие инструкции для UPO1000CS Series

Бренды по названию

Популярные бренды