background image

UDP3305S Series Programmable DC Power Supply User Manual

same specifications as brand new products. All original parts, modules, or products which were defective become 
the property of UNI-T. 

The "customer" refers to the individual or entity that is declared in the guarantee. In order to obtain the warranty 
service,  “customer  “must  inform  the  defects  within  the  applicable  warranty  period  to  UNI-T,  and  perform 
appropriate arrangements for the warranty service. 

The customer shall be responsible for packing and shipping the defective products to the individual or entity that 
is declared in the guarantee. In order obtain the warranty service, customer must inform the defects within the 
applicable  warranty  period  to  UNI-T,  and  perform  appropriate  arrangements  for  the  warranty  service.  The 
customer  shall  be  responsible  for  packing  and shipping  the  defective  products  to  the  designated  maintenance 
center of UNI-T, pay the shipping cost, and provide a copy of the purchase receipt of the original purchaser. If the 
products is shipped domestically to the purchase receipt of the original purchaser. If the product is shipped to the 
location of the UNI-T service center, UNI-T shall pay the return shipping fee. If the product is sent to any other 
location, the customer shall be responsible for all shipping, duties, taxes, and any other expenses. 

Limited Warranty and Liability 

The warranty is inapplicable to any defects, failures or damages caused by accident, normal wear of components, 
use  beyond  specified  scope  or  improper  use  of  product,  or  improper  or  insufficient  maintenance. UNI-T  is  not 
obliged to provide the services below as prescribed by the warranty: 
a) Repair damage caused by installation, repair or maintenance of personnel other than service representatives of
UNI-T;
b) Repair damage caused by improper use or connection to incompatible equipment;
c) Repair any damages or failures caused by using power source not provided by UNI-T;
d) Repair  products  that  have  been  changed  or  integrated  with  other  products  (if  such  change  or  integration
increases time or difficulty of repair).

The warranty is formulated by UNI-T for this product, replacing any other express or implied warranties. UNI-T and 
its  distributors  refuse  to  give  any  implied  warranty  for  marketability  or  applicability  for  special  purpose.  For 
violation of the warranty, repair or replacement of defective products is the only and all remedial measure UNI-T 
provides for customers. No matter whether UNI-T and its distributors are informed of any possible indirect, special, 
occasional or inevitable damage in advance, they assume no responsibility for such damage. 

Safety Information 

Warning

 

Danger:

   

To avoid electric shock and personal injury, please follow the following guidelines.

 

Disclaimer 

Please read the following safety information carefully before using the instrument. UNI-T will not be liable for the 

Содержание UDP3000S-D
































Отзывы: