background image

iv

IMPORTANT SAFEGUARDS

 

1.  READ INSTRUCTIONS - Read all safety and operating

instructions before operating this product.

2.  RETAIN INSTRUCTIONS - Retain the safety and

operating instructions for future reference.

3.  CLEANING - Unplug all equipment before cleaning. Do

not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.

4.  ATTACHMENTS - Use only attachments recommended

by the manufacturer. Non-recommended attachments
may result in the risk of fire, electric shock, or injury.

5.  WATER AND MOISTURE - Keep all equipment away

from liquids or any other type of moisture.

6.  ACCESSORIES - Do not place this television equipment

on an unstable cart, stand or table. The television
equipment may fall causing serious injury to a child or
adult, and serious damage to the equipment. Wall or
shelf mounting should follow the manufacturer’s
instructions, and should use a mounting kit approved by
the manufacturer.

7.  POWER SOURCE - The camera should only be

operated from the type of power source indicated in this
Instruction Manual.

8.  POWER CORDS - Do not allow anything to rest on the

power cord. Do not locate this product where the cord will
be abused by persons walking on it.

9.  LIGHTNING - When this product is left unattended or

unused for long periods of time, unplug it from the power
supply and disconnect it from other equipment. This will
prevent damage to the video product due to lightening
and power-line surges.

Содержание KC-2A

















Отзывы: