Ultrafly Edge 540 Скачать руководство пользователя страница 2

Dear Ultrafly Customer,

Thank you again for selecting the Ultrafly Edge 540!

This famous Aerobatic airplane has been used in many international competition & 
games. Its short fuselage & low wing loading give the airplane better agile maneuver 
capability & allow the pilots to explore its envelop limit in the extreme flight & 
competition shows. Same as the real airplane, Ultrafly has redesigned the airfoil and the 
entire fuselage to create a model that is a capable in very low speed maneuvers. For a 
small size (120cm or 47.2in) model, the wing loading usually makes the thin airfoil 
difficult to perform good pure aerobatic maneuvers, A very thick airfoil would offer good 
lift but a bit tuff in Hi-alpha approach. Ultrafly has find a good balance between the two 
and create this model that can cover the two requirement properly. We hope you can 
enjoy the fun in practicing your skill with this near TOC performance Edge 540!

We recommend you set up the power system with an Ultrafly H/12/09 brushless motor 
(500 watt) for true aerobatic maneuvers. If you just want to have a leisure sport 
experience wondering in the sky, a low cost F/18/10 with 11x5.5E propeller with 
3300mAh (15C) 3S lipo would give you enough power & duration to do so!
The battery range is from 2000 to 3300mAh 3S lipo battery. A sport/aerobatic maneuver 
would require 2000-2500mAh (20C) 3S lipo with a 12x6E APC propeller. For Extreme 3D 
maneuvers, you should consider using a 13x6.5E propeller with 2500-3300mAh (25C) 
3S lipo battery

We wish you a wonderful flying experience!

Sincerely,

Ultrafly Design Team

Содержание Edge 540






















Отзывы: