background image

Installation Guide

Installation Guide

OPERATIONS

OTHER FEATURES

Manual Transmission Remote Starters must have both the door trigger and park brake wires connected.  Most 
installs will require a clutch bypass. This is a temporary bypass. The clutch should only be bypassed during the 
activation of the remote starter. Never disconnect or alter the switch to be always bypassed. Always use a

 “M

” 

Series Remote Starter on a  manual transmission vehicle. 

Never

 install a automatic Remote Starter model  into a manual transmission vehicle. It is not recommended to 

install a remote starter on a convertible type vehicle. If doing so It is highly recommended that a radar sensor is 
installed to cover the proximity of the gear shift lever. If the radar sensor is tripped the remote starter will exit 
Reservation Mode.      

To enter Reservation Mode, the following steps must be followed.
Step 1

 - While  the vehicle is running, place the transmission in neutral and apply the parking brake. 

Step 2

 - Press and release the brake pedal. The park lights will activate.

Step 3

 - Turn the ignition key off and the vehicle will stay running.

Step 4

 - Exit the vehicle and close the door. The vehicle will then shut off

*

.

Step 5

 - The vehicle can now be safely remote started.

If the vehicle has a dome light delay, the vehicle may stay running until the dome light turns off. This is normally 

no longer than 30 seconds.

 

Reservation Mode  will automatically be exited if the doors of the vehicle are opened. 

The set-up mode will then have to be repeated . Reservation Mode Must be set-up each time the vehicle is 
parked.

        Note: If the vehicle is not in Reservation Mode and the Start button is pressed, the system will
          flash the park lights four times slowly. 

Reservation Mode - Manual Trans.

13

12

Emergency Service Mode - (Valet Mode) 

This feature will disable the system except for locking and unlock functions. 
This mode can also used  if a remote is lost, damaged or if the system malfunctions.

ENTERING SERVICE MODE

1.Turn the ignition key to the “On” position then  press and hold the Program 

 

Button on the 

antenna for 5 seconds or until the siren chirps 

 5

 

 times.

EXITING SERVICE  MODE

1.Turn the ignition key to the “On” position then press and hold the Program

 

Button for 5 

seconds or until the siren chirps  

2 times.

Note: Remote starter functions will be disabled and the LED will be “on” steady.   
          The door locks and the  trunk release will  still be operational.

Ignition 

“On”

7 sec.

ATTENTION:

 THE SYSTEM MUST BE PLACED INTO SERVICE MODE BEFORE ANY UNDER HOOD 

SERVICING IS DONE TO THE VEHICLE.  IT IS THE  RESPONSIBILITY OF THE VEHICLE’S OWNER TO 
INSURE THAT THIS IS DONE.  THE MANUFACTURER ACCEPTS NO RESPONSIBILITY FOR 
ACCIDENTAL STARTING WHILE VEHICLE IS BEING SERVICED.

Battery Replacement 

1

Lift

Slide

+

-

System Service Mode (Valet) - By Remote

This feature will disable the system from the remote transmitter. Use this feature must be 
used when having the vehicle serviced. ( Oil change, Tune-up etc.)

ACTIVATE Service Mode (User Programmable Feature)

1 - Press and hold button #4 for 3 seconds. (The remote will beep twice)
2 - Press button #1 Five times or until the 

?

 starts flashing on the LCD screen.

3 - Press button #3 and the 

symbol will come on solid.

4 - Press button #4 to exit User Program Mode.

(System Is Now In Service Mode)

5 - The siren will chirp once and the LED’s on the antenna will come on solid.

DEACTIVATE Service Mode

1 - Press and hold button #4 for 3 seconds. (The remote will beep twice)
2 - Press button #1 Five times or until the 

?

 starts flashing on the LCD screen.

3 - Press button# 2 and the 

symbol will turn off.

4 - Press button# 4 to exit User Program Mode.

(Serice Mode is Deactivated)

5 - The siren will chirp once and the LED’s on the antenna will turn off.

Note: Remote starter functions will be disabled and the LED will be “On” steady. 
The door locks and the  trunk release will  still be operational.

Quick Timer (Selects Last Programmed Start Interval)

1. Enter Transmitter Program Mode.
2. The Telephone Icon will begin to flash on the LCD screen.
3. Press Button #3 and the Telephone Icon will come on solid and the key Icon will begin to flash.
4. Press Button #4 to exit Transmitter Program Mode.
5. The remote starter will now start in the last programmed start interval.

Note: Timer Mode will reset if the ignition key is turned to the “On” position. If this occurs the above 
steps will have to be repeated.

 

When the Battery Icon on the remote indicates that the battery is low the battery should be changed 

promptly. Replace with quality 1.5volt “AAA”  battery. 

Transmitter Operation  

1

2

3

4

1

2

3

4

4 - 3

2 & 3

1 & 3

Press Once to Lock / Unlock Doors and arm/disarm the alarm.
Press 2nd Time (within 3 sec.) and Hold for Constant Lock Output. 
Press and hold for 3 seconds to activate Panic Mode.
Press again to disable panic when activated. 
 While running with the key, press the button to activate Idle Mode.                                                                                

Press and Hold for Trunk / Aux Output 

*Note this will also unlock doors and disarm alarm

Press Once for Start - (

2 Times if programmed for Safety Start

).

Press and Hold for 3 seconds while running to turn off.
 While running with the key, press the button to activate Idle Mode.                                                                                

Press and Release for Status Check.
Hold for 3 seconds to enter User Programmable Features
While running with the key, press and release to activate Turbo Timer Mode.

Press and release button #4  then press and hold button #3  for three seconds to 
activate/Deactivate the Timer Mode 

Press both buttons for 3 seconds to activate Car Finder Mode  or 5th channel (see 
page 9, setting 6)

Press both buttons for 1-2 seconds to activate 4th Channel (see page 9, setting 4)

Содержание 4500

















Отзывы: