Ultra Max UM-2100-762 Скачать руководство пользователя страница 9

Страница: 9 / 54

Rev B

QUI

Step 9: Enter Hardness (762 Demand Control Only)

•

Enter inlet water hardness at installation site.

•

Default hardness setting is 25 grains (25 ppm for metric)

•

To change hardness, press SET to make the setting flash. Use the UP and

DOWN buttons to scroll to the correct hardness.

•

Press SET to accept the entered hardness value.

•

The control will return you to the normal operation mode.

Initial system programming is now complete. The control will return to normal
operation mode, if a button is not pushed for 30 seconds.

For system start-up procedure, including: purging the mineral tank, refilling the regenerant tank, and drawing

regenerant, see

Initial Startup Step-By-Step Instructions

on page 29.

Manual Regeneration Procedures

To Initiate a Manual Regeneration:

•

Press REGEN once for delayed regeneration.
System will regenerate at next set regen time (2:00 AM).

A flashing regen (recycle) symbol will be displayed.

•

Press and hold REGEN for 5 seconds to initiate immediate manual

regeneration. A solid regen symbol will be displayed.

•

After immediate regeneration has begun, press REGEN again to initiate a

second manual regeneration. An X2 symbol will be displayed, indicating a

second regeneration will follow the first regeneration.

During a Regeneration:

•

A "C#" is displayed to show current cycle.

•

Total regen time remaining is displayed on screen.

•

Press and hold SET to show current cycle time remaining.

To Advance Regeneration Cycles:

•

Press and hold SET - showing current cycle time.

•

Simultaneously press SET and UP to advance one cycle.
An hourglass will display while cam is advancing.

When cam reaches next cycle, "C2" will be displayed.

•

Repeat SET and UP to advance through each cycle.

•

Press and hold SET and UP buttons for 5 seconds to cancel regen.
Hourglass will begin flashing, indicating regen is cancelled.

Camshaft will advance to home - may take 1-2 minutes.

Regeneration Cycles:

•

C1 - Backwash

•

C2 - Regenerant Draw/Slow Rinse (not used in filter mode)

•

C3 - Slow Rinse (not used in filter mode)

•

C4 - System Pause (to repressurize tank)

•

C5 - Fast rinse

•

C8 - Regenerant refill (not used in filter mode)

Time & Day

Regen Time & Day

Salt

SU MO TU WE TH FR SA DAYS

Capacity

Hardness

MIN

Cycle Indicator

Regen Symbol

Second Manual Regen Symbol

Содержание UM-2100-762























































Результаты поиска

Содержание UM-2100-762

Отзывы:

Похожие инструкции для UM-2100-762

Бренды по названию

Популярные бренды

Ultra Max UM-2100-762, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UM-2100-762

Отзывы:

Похожие инструкции для UM-2100-762

Бренды по названию

Популярные бренды