Ultra electronics VersaMux-4000 Скачать руководство пользователя

Страница: 123 / 180

Chapter 6: Diagnostics

Diagnostics Menu

Part No. 24001157

VersaMux-4000 Operation & Installation Guide

Page 6-7

Revision C

Front Panel

Interface

Figure 6-3

shows how to navigate the

Diagnostics

sub-menu from the front panel

interface.

Figure 6-3

Diagnostics Sub-Menu from the Front Panel Interface

Loopbacks

The

Loopbacks

sub-menu enables you to initiate a loopback for diagnostic

purposes. Selecting

Loopbacks

enters a sub-menu with the following items:

•

Aggregate

•

Port-1

•

Port-2

•

Port-3

•

Port-4

When you chose an interface (aggregate, or one of the ports), the following
loopback types can be chosen:

•

No Loop –

This option terminates the current loopback operation.

•

Bi-directional –

This option provides a loopback both toward:

•

the user port and aggregate on a port module.

•

the aggregate port and the multiplexer/demultiplexer (mux/
demux) circuitry on an aggregate module.

•

Internal

- This option provides a loopback toward:

•

the aggregate on a port module.

•

the multiplexer/demultiplexer (mux/demux) circuitry on an
aggregate module.

•

External

- This option provides a loopback toward:

•

the user port on a port module.

•

the aggregate port on an aggregate module.

See

“Internal Loopbacks” on page 6-8

and

“External Loopbacks” on page 6-9

for

loopback diagrams and more information.

Diagnostics

Loopbacks

BERT

Hot-Swap

Test

Loopbacks Sub-Menu

BERT Sub-Menu

Hot-Swap Options

Test Sub-Menu

Содержание VersaMux-4000





















































































































































































Результаты поиска

Содержание VersaMux-4000

Отзывы:

Похожие инструкции для VersaMux-4000

Бренды по названию

Популярные бренды

Ultra electronics VersaMux-4000, Руководство по эксплуатации и установке

Результаты поиска

Содержание VersaMux-4000

Отзывы:

Похожие инструкции для VersaMux-4000

Бренды по названию

Популярные бренды