Ultra electronics VersaMux-4000 Скачать руководство пользователя

Страница: 124 / 180

Diagnostics Menu

Chapter 6: Diagnostics

Page 6-8

VersaMux-4000 Operation & Installation Guide

Part No. 24001157

Revision C

Internal Loopbacks

Figure 6-4

illustrates an internal loopback on a port module. The internal loopback

sends the transmit data from the aggregate back to the aggregate as the receive
data. In addition the transmit data continues on to the user port.

Figure 6-4

Internal Loopback Diagram for a Port Module

Figure 6-5

illustrates an internal loopback on an aggregate module. The internal

loopback sends the transmit data from the multiplexer/demultiplexer back to the
multiplexer/demultiplexer as the receive data. In addition the transmit data
continues on to the aggregate port.

Figure 6-5

Internal Loopback Diagram for an Aggregate Module

Tx Data

Rx Data

Aggregate

Port Module

User Port

Tx Data

Rx Data

Mux/Demux

Aggregate Module

Aggregate Port

Содержание VersaMux-4000





















































































































































































Результаты поиска

Содержание VersaMux-4000

Отзывы:

Похожие инструкции для VersaMux-4000

Бренды по названию

Популярные бренды

Ultra electronics VersaMux-4000, Руководство по эксплуатации и установке

Результаты поиска

Содержание VersaMux-4000

Отзывы:

Похожие инструкции для VersaMux-4000

Бренды по названию

Популярные бренды