background image

 

Page 

15

 of 

28

 

Issue 5 

– 16/12/2020 

 

10.  Transport Mode 

 

 

 
 
 
 

 

If the patient is being moved on the mattress, or there is a 

power cut, general pressure can be maintained in the system 

for an adequate period of time whilst disconnected from the 

mains. 

 

Simply disconnect air pipe connector and place the connector 

cover over it. The air pressures in the mattress will now 

equalise, but maintain a degree of comfort. This will maintain 

the cells in their present state for approximately 48 hours. 

 

It is important to restore the Heritage II Digital dynamic 

replacement mattress as quickly as possible by reconnecting 

the supply tubes to the power unit. 

 

11.  Alarms & Fault Findings 

 

The Heritage II Digital is equipped with audible and visual alarm indicators. These alert the user to the 

status of the available mains supply and any mattress defect. 
 

11.1  Low pressure alarm 

 

Upon detection of low pressure, an audible alarm will be heard and the 

Low Pressure

 indicator will 

illuminate. The audible alarm may be cancelled by pressing the 

Alarm Mute

 button.

 

The 

Low 

Pressure

 indicator will continuously illuminate until the low pressure fault condition is resolved.  

 

This condition could be caused, for example, by incorrect fitting of the air pipe connector, opening of 

the CPR valve or a leak in the mattress due to a cut or puncture. 
 

11.2  Power failure alarm 

 

If at any time the mains power should be removed from the power unit or the power cable is 

unplugged without turning the power unit OFF, an audible alarm will be heard and the 

Power Failure

 

indicator will illuminate. The audible alarm may be cancelled by pressing the 

Alarm Mute

 button. 

 

 

 

Note: When the power unit has not been used for more than 3 months, it might 
require 60 minutes operating time (or more) for the Alarm to function correctly.

 

 

11.3  Service (alternating failure alarm) 

 

Should your system develop a fault condition whilst in use, an audible alarm will be heard and the 

Service

 indicator will illuminate. Please refer to 

Table 1

 for error codes and call Ultimate Healthcare 

or your local distributor.

  

 
 

Содержание UPRA3678DT-2





























Отзывы: