UINICS CU-675 Series, Руководство по эксплуатации

Страница: 5 / 44

- 2 -
2．Specifications
【 Standard specifications 】 Table.１
Item Specifications
M
e
a
s
u
r
e
m
e
n
t
Mesurement accuracy
(accumulate)
Scaling（Conversion instrument）± 0 to the 1
(At the time of correction display current position and function
stop)
Total display Upper tier：6 Digits red color LED character height10mm
PV display（Measured value） Middle tier：6 Digits red color LED character height10mm
SV display（Target value） Lower tier：6 Digits red color LED character height8mm
CH display
Lower tier：6 Digits red color LED character height8mm
Analog input display ＡＮＡ Lamp Lighting （orange 3φＬＥＤ）
Control signal display ＲＵＮ Lamp Lighting （green 3φＬＥＤ）
Slow down signal display ＳＬＷ Lamp Lighting （green 3φＬＥＤ）
End signal display ＥＮＤ Lamp Lighting （green 3φＬＥＤ）
Normal stop display ＳＴＰ Lamp Lighting （green 3φＬＥＤ）
Deviation error display ＳＴＳ Lamp Lighting （red 3φＬＥＤ）
Measurement error display ＡＬＭ Lamp Lighting （red 3φＬＥＤ）
Manual state display
ＭＡＮ Lamp Lighting （orange 3φＬＥＤ）
Measurement display
Range
TOTAL
0～999999
more than 999999 was flashing display
（Non-zero suppression）
PV
(Measured alue）
SV Setting of range Target value 0～999999
Scaling（Conversion value） 1×10
-9
– 9999 (selectable)
Decimal point
Displays 1 - 3 decimal points. (selectable)
PV display reset Use the start key or start signal for reset, start of surveying
from 0.
（Selection when reset start）
Keep reset key is ON for more than two seconds
Terminal block is ON for more than 100mS
Over run correction Compensation beyond the value from SV value (Target value)
(Arbitrarily set the be stopped value before In 00000～99999 of
ＳＶ value.）
Sonsor input
anomaly detection
If there is no input of set number of pulses in the set time、
Outputs the abnormal signal measurement, Measurement abnormal
display lights（ＡＬＭ）,batch control stop.
S
e
n
s
o
r
Input signal
NPN Open Collector pulse, Or input voltage pulse.
（Setting can be switched in DIP SW）
Input level
NPN Open Collector pulse： MIN 10mA or more（Sink current）
Voltage pulse：LOW Level 2.0V or lower HI Level 3.8～30V
Input response
LOW：0.01Hz～50Hz HI：0.01Hz～10kHz
However, when duty 50%
Sensor power
Standard DC＋12V（±10％）100mA MAX（Stabilization）
Option DC＋24V（±10％） 60mA MAX
S
i
g
n
a
l
Reset signal
Terminal block input is ON for more than 100ms
NPN Open Collector output,accept short output
ＰＶdisplay reset and Release error
Sink current：more than MIN 10mA
Start signal
Stop signal
Abnormality signal
Ban signal
Terminal block input is ON for more than 100ms
ＮＰＮ Open Collector output,accept short output
Sink current：more than MIN 10mA