UfiSpace M3000-14XC Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 31

background image

M3000-14XC Hardware Installation Guide | 22

12

Cable Connections

Connecting the USB Extender Cable

Connect the USB 2.0 A

Type plug (male connector) into the USB port (female connector) located on

the front panel of the equipment. The USB port is a maintenance port.

Figure 28.

Connecting a Cable to the ToD Interface

1.

Connect one end of a straight-through Ethernet cable to the GNSS unit

2.

Connect the other end of the straight-through Ethernet cable to the port marked

“TOD”

located on the front panel of the equipment.

Figure 29.

«
...
23
24
25
26
27
...
»

Содержание M3000-14XC
































Отзывы:

Нет отзывов

Похожие инструкции для M3000-14XC

Бренд: B&K Страницы: 23

Бренд: GW Instek Страницы: 3

Бренд: PalmSens Страницы: 13

Бренд: BK Precision Страницы: 4

Бренд: Benning Страницы: 78

Бренд: CEN-TECH Страницы: 9

Бренд: Vorel Страницы: 6

Бренд: Gossen MetraWatt Страницы: 70

Бренд: Raisecom Страницы: 14

Бренд: koban Страницы: 80

Бренд: koban Страницы: 72

Бренд: koban Страницы: 98

Бренд: National Instruments Страницы: 11

PAN Pocketmeter

Бренд: PANCONTROL Страницы: 186

Бренд: UNI-T Страницы: 55

Бренд: IDEAL Страницы: 23

Бренд: IDEAL Страницы: 40

SECULIFE HIT MD

Бренд: Gossen MetraWatt Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды