OFF
Indicates that the iron is switched off on
stand-by state.
SILK
Indicates that the selected ironing temperature
is suitable for silk and synthetic fabrics.
WOOL
Indicates that the selected ironing temperature
is suitable for wool.
COTTON
Indicates that the selected ironing temperature
is suitable for cotton.
LINEN
Indicates that the selected ironing temperature
is suitable for linen.
Indicates that the option of temperature of the
iron is selected.
Indicates that the level of temperature of the
iron is selected.
The correspondence of the symbols that are displayed on the
clothing label with the iron is the following one:
Silk and synthetic fabric
(SILK)
Wool
(WOOL)
Cotton
(WOOL)
MAX
Linen
(LINEN)
The iron is very simple to use:
- When it is plugged in, the display screen lights up and then the iron
goes into stand-by (OFF) state.
- To increase the temperature of the sole plate, please press the key
successively. The iron goes through the following cycle:
OFF
SILK
WOOL
COTTON
LINEN
- To decrease the temperature of the sole plate, please press the key
successively. The iron goes through the following cycle:
LINEN
COTTON
WOOL
SILK
OFF
The indicating symbols of the selected iron temperature blink until
the sole plate reaches the operation temperature, either warming up
or cooling off.
BEFORE USING THE IRON FOR THE FIRST TIME
Remove any label or protective cover from the soleplate.
With the unplugged iron, fill in the tank of the iron with water from
the water supply system. Plug in the apparatus and place it on its
supporting heel in the vertical position. Select the level of temperature
“LINEN”
.
When the steam iron has reached the desired temperature (the
temperature indicating symbols stay blinking), start steaming by
setting the steam regulator to the
“3”
level and by repeatedly pressing
the steam button .
When using the steam function for the first time, do not apply it on the
laundry, as there could still be dirt in the steam dispenser.
Your new iron may smell and give off some smoke when
you use it for the first time, this is normal and will cease
after a short while.
HOW TO USE THE IRON
The temperature indicating symbols blink when the iron is warming
up, and stop blinking as long as the selected temperature is
reached.
Once the iron has warmed up, it is ready now for ironing, and also
during the following heating phases of the same mode.
In the same way, the symbols blink when the iron is cooling off while
passing from a higher temperature of ironing to a lower one, and stop
when reaching the selected temperature (the temperature drop can
last several minutes).
Check the laundry care label for the required ironing temperature. If
you do not know what kind or kinds of fabric an article is made of,
determine the right ironing temperature by ironing a part that will not
be visible when you wear or use the article.
First start ironing the clothes which require the lowest temperature of
ironing such as synthetic fabric
“SILK”
.
Silk, woollen or synthetic materials: iron the reverse side of the fabric
to prevent shiny patches. Avoid using the spray function to prevent
stains.
FILLING THE WATER TANK
1
Set the steam regulator to the “
0
” position and unplug
the iron from the mains!
Use only clean water from the tap without mixing anything with it.
The addition of other liquids, such as perfume, will damage the
appliance.
Do not use ineligible products, since they can damage the
apparatus.
Any damage caused by the use of the above mentioned
products will cause the guarantee cancellation.
Do not use condensation water from tumble dryers, air conditionings
or similar. This appliance has been designed to use normal tap
water.
To prolong the optimum steam function, mix tap water with distilled
water 1:1. If the tap water in your district is very hard, mix tap water
with distilled water 1:2.
Never fill beyond the
“MAX”
water level mark.
GETTING READY
2
Remove any label or protective cover from the soleplate.
Wait until the iron reaches the selected temperature (the temperature
indicating symbols stop blinking).
IRONING WITHOUT STEAM
3
Set the steam regulator to the
“0”
position. Select the appropriate
temperature for each type of clothing material.
IRONING WITH STEAM
4
Set the steam regulator to the
“1”
position or superior one.
It is advisable to use the steam iron when the temperature of the sole
plate corresponds to
“COTTON”
and
“LINEN”
.
SPRAY
5
Press the button
Do not use the spray function with silk.
SHOT OF STEAM
6
To select the temperature level
“LINEN”
,
please press the button repeatedly.
Interval between shots of steam should be 5 sec.
VAPOR VERTICAL
7
Do not iron clothing while it is being worn!
Never direct the steam at persons or animals!
To select the temperature level
“LINEN”
,
