UFESA AS5200, Инструкция по эксплуатации

Страница: 13 / 58

Prepare the vacuum cleaner to use
1
Insert the tip of the suction hose to the vacuum
cleaner inlet. The characteristic “click” indicates
a properly fitted hose.
2
The second end of the hose (a handle) connect to
telescopic suction tube.
3
Set the telescopic suction tube to the desired
length by sliding the slider according with arrow and
put out / slide out the tube.
4
On the other end of the suction tube install the
appropriate sucker or brush.
5
Use combination carpet & floor brush for vacuuming
both hard surfaces and carpets. To clean hard surfaces
– wooden floors, plastic floors, ceramic tiles etc. pull out
the brush by pressing the switch on the combination
brush according to the figure . Retract the brush
when vacuuming carpets (set the switch in “ ”).
6
Catch the connection cable plug
(3)
and draw it
out from the vacuum cleaner.
When drawing out the power cable you
have to pay attention to yellow band
indicating the end of the cable drawn out.
Further attempts (jerks) may lead to damage of
the cable.
7 Plug the cord into an AC outlet.
Before you start vacuum cleaner make sure whether
the dust container “CYCLONE” is mounted in chamber
of the vacuum cleaner, and whether the inlet and outlet
filters are mounted in the vacuum cleaner.
8
Start the vacuum cleaner by pressing On/Off
button (4) .
9
Vacuum cleaner is equipped with electronic power
regulator, which - during the vacuuming - can smooth
control the suction power of vacuum cleaner. By
turning the knob (4) right or left – you can increase or
decrease the suction power.
10
Vacuum cleaner is also equipped in mechanical
control of suction power (9) , which is located on the
handle of the hose. It can temporarily slightly adjust the
suction power, without adjustment done with knob (4) .
B
Disassembly/assembly of
“CYCLONE” dust container
Vacuum cleaner is equipped in removable dust
container “CYCLONE” (which is a removable segment
of vacuum cleaner), which accumulates contaminants.
As soon as the “CYCLONE” dust container is full,
it should be emptied.
Vacuum cleaner is equipped with
a safety valve which is located in the
chamber of the “CYCLONE” dust
container. The valve is activated (open)
automatically when a total jam (occlusion) occurs
on the sucking hose or this happens to equipment
connected to it, as well as in the case of excessive
overfill of “CYCLONE” dust container. When the
valve is open you can hear a characteristic sound
(“a sound of flutter”) in the vacuum cleaner.
1
Vacuum cleaner is equipped with a dust container
“CYCLONE” full indicator (5) . When the gap of dust
container “CYCLONE” full indicator is totally filled with
red mark during operation (vacuum cleaner operates at
full power and sucker nozzle or brush is upraised over
cleaned surface) so this informs that there is a need
to empty the dust bin “CYCLONE”. The dust container
“CYCLONE” full indicator
(5)
may work also in the
case of clogging of the suction hose or clogging of
equipment connected to the hose.
2
Switch off the vacuum cleaner by pressing On/Off
button (4) .
3
Take off the cable connection plug from the wall
outlet.
4
Press the two side buttons on the hose end, then
remove the hose end from vacuum cleaner inlet hole.
5
Raise the hook to unlock the dust container
“CYCLONE” (7) and remove dust container “CYCLONE”
(16) from the vacuum cleaner.
6
Move the dust container “CYCLONE” on garbage
trash. Press the button located on dust container
“CYCLONE”, the bottom of the container will open and
the contents will fall out to the trash.
7 After emptying the container, snap the bottom. Pay
attention to the fact that a seal located on the bottom
of container must be correctly positioned.
Container must be precisely closed.
Otherwise the dust will penetrate the
vacuum cleaner chamber and the suction
power will decrease.
C