Ublox EVK-NORA-W101 Скачать руководство пользователя страница 2

 

EVK-NORA-W1 - User guide 

UBX-22002764 - R02 

Document information

 

Page 2 of 22 

C1-Public  

 

Document information 

Title 

EVK-NORA-W1 

Subtitle 

Evaluation kit for NORA-W10 series modules 

Document type 

User guide 

 

Document number 

UBX-22002764 

 

Revision and date 

R02 

22-Jul-2022 

Disclosure restriction 

C1-Public 

 

 

Product status

 

Corresponding content status 

 

In development / 
Prototype 

Objective specification 

Target values. Revised and supplementary data will be published later. 

Engineering sample 

Advance information 

Data based on early testing. Revised and supplementary data will be published later. 

Initial production 

Early production information  Data from product verification. Revised and supplementary data may be published later. 

Mass production/ 
End of life 

Production information 

Document contains the final product specification. 

 

This document applies to the following products: 

Product name 

Document status 

EVK-NORA-W101 

Objective specification 

EVK-NORA-W106 

Objective specification 

 

For information about the hardware, software, and status of the available product types, see the 
NORA-W10 data sheet 

[1]

 

 

u-blox or third parties may hold intellectual property rights in the products, names, logos and designs included in this 
document. Copying, reproduction, modification or disclosure to third parties of this document or any part thereof is only 
permitted with the express written permission of u-blox. 

The information contained herein is provided “as is” and u

-blox assumes no liability for its use. No warranty, either express or 

implied, is given, including but not limited to, with respect to the accuracy, correctness, reliability and fitness for a particular 
purpose of the information. This document may be revised by u-blox at any time without notice. For the most recent 
documents, visit www.u-blox.com.  
Copyright © u-blox AG. 

Содержание EVK-NORA-W101























Отзывы: