Note:
Every time the heater is switched on, it will heat at high temperature for 2
minutes. The heater will then operate according to the instructions below. When the
room temperature reaches the desired set temperature or if the set temperature is
lower than or equal to the room temperature, the heating element will shut off
immediately. However, the fan motor will continue to run for about 15 seconds before
shutting off. This is a safety feature that is designed to protect the unit from
overheating.
CAUTION:
This heater includes an Overheat Protection System that shuts the unit off if it
overheats due to abnormal conditions. If this occurs, turn the heater off, unplug it, and check
CAUTION:
This heater includes a safety tip-over protection feature which will shut the
heater off in case it is tipped over. If, at any time, the heater does tip over, please put the
heater back in the upright position. The heater will resume its normal operation.
for
and remove any objects on or adjacent to the heater. Allow it to cool for a few minutes,
plug it back in, and resume normal operation.
5
INSERTING BATTERIES
1. Press down on the battery compartment cover and slide it out.
2. Insert the batteries, making sure that the positive terminals are facing
the proper direction marked inside the battery compartment
3. Close the cover by sliding it in.
Notes: 1) Use 2 “AAA” batteries (NOT INCLUDED).
2) Do not mix old and new batteries.
3) Do not mix alkaline, standard (carbon-line) or rechargeable
(nickel-cadmium) batteries.
4) Remove the batteries from remote if is to be left unused for a long period of time.
remote
battery
cover
USING THE REMOTE CONTROL
The remote has 6 keys that have following functions:
Press to switch the heater on,press again to switch off
Press this key to select the desired mode (HI LO ) or return to standby mode
Value adjustment key, press it to increase temperature setting or increase timer setting
Value adjustment key, press it to decrease temperature setting or decrease timer setting
Press this key to set the timer
Press this key to start or stop the oscillation
3’
Place the heater on a firm level surface that is free of obstructions, at least
(0.9 m) away from all walls, furniture, curtains, plants or flammable
materials.
Plug the heater into a grounded 120 V outlet. The buzzer will sound and the
digital indicator will display the room temperature. When the heater is
switched on, the buzzer will sound whenever a key is pressed.
Power setting: Press the power key
, the operating modes are arranged in
sequence
a circular
(
HI-LO- ).
: The fan circulates room air only, the heating elements are off.
LO:
The Fan and heating elements operate at 900 W.
HI:
The Fan and heating elements operate at 1500 W.
Temperature setting: When the heater is set to HI or LO, press the UP key
and DOWN key to set the desired temperature between 5
℃
to 35
℃
in
Oscillation setting: The heater will oscillate by pressing the oscillation key
once. To stop the oscillation, press this key again. This key is only valid when
the heater is working.
Timer setting: When the heater is on, it can be set to turn off automatically in 0.5
to 9.5 hours.
increments of 1° C. If there is no further operation within 5 seconds, the setting
will be saved. Once the temperature is set, the unit will select the operating
mode based on the following 2 conditions:
a. If the set temperature is higher than the room temperature, the
heater will continue to heat until the room temperature reaches the
set temperature. Once the room temperature reaches the set
temperature, the heater will stop heating. The heater will resume
heating when the room temperature falls below the set temperature.
The heater will switch on and off in order to maintain the set
temperature.
b. If the set temperature is lower than or equal to the room
temperature, the temperature display will flash
,
and the unit will stop
heating. When the room temperature falls to below the set
temperature, the unit will resume heating. The heater will switch on
and off in order to maintain the set temperature.
4
a. Press the Timer key. The display will blink.
b. Press the Increase key and Decrease key
to set the desired
time for the unit to turn off.
c.
After settings have been made, the display will change back to
show the room temperature.
d. To cancel the timer, press the timer pad and press the Increase key
and Decrease key
until 0.0 appears in the display.
e. If the timer was set before a power outage, it will need to be reset after
power is restored.
