UBERHAUS DESIGN 83035033 WW11994, Руководство оператора, Страница: 5 / 11

4
OPERATING INSTRUCTIONS
Using the Control Panel:
Master Power Switch (A)
Open the cover and push button A down (I) to “On”position. (see FIG A)
Flame Effect:
Push “ O/I ” (On/Off) button (B) or “ O/I ” (On/Off) button (M) on the remote control to begin
The flame effect can be adjusted by pressing the dimmer “ ”button (C) or dimmer
“ ”Button (L) on the remote control. When pressed, the
red light will blink and
the flame effect will cycle from high to low. Press the dimmer “ ”button (C) or dimmer
“ ”button(L) on the remote control again to lock in desired flame brightness. The red
light “ ”will remain on.This brightness will be kept until the dimmer “ ”button (C) or
dimmer “ ”button (L) on the remote control is pressed again
.
Heat setting:
Turning on Master Power Switch (A) and “ O/I ” ( On/Off) button (B) or “ O/I ” buttom (M) on
the remote control.
Press “
650W ” button (D) or “ 650W ” button (K) on the remote control to active the low
heater setting. The red light above will indicate that the heater is functioning.
Press “ 650W ” button (D) or “ 650W ” button (K) on the remote control again to shut off the
heater.
Press “
1300W ” button (E) or “ 1300W ” button (J) on the remote to active the high heater
setting.The red lights above “ 650W ” and “ 1300W ” buttons will indicate that the heater
is functioning on high
.
Press “ 1300W ” button (E) or “ 1300W ” button (J) on the remote control again to shut off
the heater.
Note
When the heater begins to work, it will give off cool air for about 10 seconds before the
heating function is activated.
flame effect. The red power light “ ”and dimmer light “ ”will automatically come on.
Control Panel
Plugging in the heater
Note:
1) This heater is for use on 120volts.
2) A 15AMP circuit is required to operate this appliance.If the breaker
trips when the appliance is running, you may need to move the
appliance to another location or unplug other appliances that are on the same circuit.
Note
dim or does not operate properly at first, ensure that the light bulbs
are properly secured in the sockets (bulbs should be finger tight, do
not over Light Bulb” Section of the manual for tighten). See "Replacing
When you first turn the heater on, it may emit a slight but harmless
odor
from certain oils or greases being heated as the appliance resulting
is used for the first time. This odor is perfectly safe and will stop
shortly. It will not reoccur after the first operation of this appliance.
This appliance comes equipped with an overheat protection safety
device. Should the appliance begin to overheat for any reason, it will
automatically turn all heater functions of the appliance off. The
appliance will have to be reset
prior to continuing use. To reset the
overheat protection safety device, turn all controls off and unplug
the appliance, wait 10 minutes, plug the appliance back in and
turn on. If the appliance continuously overheats, please call our
customer service department toll free at 1-866-206-0888.
Fig B
Access Panel
Screws
Light
Bulbs
MAINTENANCE
WARNING: Before attempting to perform any maintenance on this
appliance
,
turn all controls to the “OFF”position and unplug
.
Allow
the appliance to be “OFF” for at least 10 minutes before performing
any maintenance in order to allow all components to cool properly.
CLEANING:
1.To remove dust from glass window, use a clean dry cloth.
2.To remove fingerprints or other marks from glass window, use a
clean damp cloth. Do not spray glass cleaner or other liquids
directly onto the window.
3.Clean metal surfaces with a clean damp cloth making sure not
to push dust or debris into any air intake or exhaust vents.
4.Do not use abrasive cleaners or spray liquids on any part of
the appliance.
5.Periodic cleaning/vacuuming of the fan/heater unit is
strongly recommended to ensure that no dirt or foreign
objects build up.
TO REPLACE THE LIGHT BULBS (see FIGURE B
)
1
.
Take off the front glass panel
.
2
.
Remove the twelve screws from the side panel
,
located on the front of the unit
,
and remove front panel
.
3
.
Locate and examine the bulbs to determine which
bulb
(
s
)
require replacement
.
4
.
Unscrew the bulb
(
s
)
counter clockwise
.
5
.
Insert new bulb
(
s
).
6
.
Secure front panel to unit
.
WARNING:
Do not exceed the
recommended bulb wattage. Use
only 120V, 40W,E12 Chandelier
Light Bulb, Candelabra Base. The
lamp holder is model E12.
Hint: It is a good idea to
replace all light bulbs at one
time if they are close to the end
of their life.Group replacement
will reduce the number of times you
need to open the unit to replace
light bulbs.
instructions.
Light bulbs may become loose during shipping. If the flame effect is
Using the Remote Control:
This heater includes a remote control.To operate the appliance using
the remote control,the Master Power Switch (A) must be
the“ON”position. See below for directions to use the remote control:
1300W Heater Button (J):
Push “1300W” button once to
active high heat setting.
Push second time to turn the
heater off
Dimmer Button(L):
Adjust the brightness
of the flame effect
650W Heater Button (K):
Push “650W”button once to
active low heat setting.
Push second time to turn
the heater off
ON/OFF Button (M)
Flame effect
Note:
Direct the remote control towards
the appliance at a distance between
1-5 meters
to function properly.The remote
control receptor is located in the
control panel(F)
for the remote control
Battery Warning Statement:
- Do not mix old and new batteries
- Do not mix alkaline, standard (carbon-zinc),
or rechargeable (ni-cad, ni-mh, etc) batteries.