background image

 

10 

 

2.8.

 

Safety requirements 

 
 

            The device complies with Class I of electrical safety. 

Before connecting the chest freezer to the electric power network, 

make sure that  

 

the  network  voltage  corresponds  to  the  value  given  on  the 

device nameplate (+10%, –15%); 

 

the power cord and plug are not damaged. 

The  chest  freezer  must  be  connected  to  a  grounded  power  supply 

socket.  Do  not  connect  the  freezer  to  a  power  supply  with  a  faulty 
overcurrent protection. Check this before starting the installation process. 

Do not use any adapters, additional sockets or extension cords that 

do not match the current load of the device. 

If there are signs of faulty wiring (smell, smoke), disconnect the power 

supply to the device and call a service technician to remedy the fault. 

It  is  forbidden  to  operate  the 

chest freezer: 

if the nominal supply voltage indicated on the nameplate deviates 

by more than + 10% - 15%. 

in case of high level of humidity and dustiness of the environment 

(relative humidity above 75%, when ceiling, walls, floor and other 
objects in the room are covered with moisture); 

 

 

Содержание BEST



































Отзывы: